- 您现在的位置：买卖IC网 > PDF目录19639 > YS12S16-0G (Power-One)CONVERTER DC-DC 12V 16A SMD PDF资料下载
参数资料
| 型号： | YS12S16-0G |
| 厂商： | Power-One |
| 文件页数： | 5/27页 |
| 文件大小： | 0K |
| 描述： | CONVERTER DC-DC 12V 16A SMD |
| 标准包装： | 1 |
| 系列： | Y |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 9.6V |
| 电压 - 输入（最大）： | 14V |
| Voltage - Output 1： | 0.75 ~ 5.5 V |
| 电流 - 输出（最大）： | 16A |
| 电源（瓦） - 制造商系列： | 88W |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-DIP SMD 模块 |
| 尺寸/尺寸： | 1.30" L x 0.53" W x 0.31" H（33.0mm x 13.5mm x 7.9mm） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 94.8% |
| 电源（瓦特）- 最大： | 88W |
| 产品目录页面： | 2739 (CN2011-ZH PDF) |
| 其它名称： | 179-2368-6 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
YNS12S16 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 16 A
Nex - s Series
Operation
Vin
TM
Converter
SENSE
Input and Output Impedance
R*
ON/OFF
(Top View)
Vout
The Y-Series converter should be connected via a
Vin
low impedance to the DC power source. In many
applications, the inductance associated with the
GND
TRIM
Rload
distribution from the power source to the input of
the converter can affect the stability of the
converter. It is recommended to use decoupling
capacitors in order to ensure stability of the
converter and reduce input ripple voltage. The
converter has internal input capacitance of 40 μ F
with very low ESR (ceramic capacitors).
In a typical application, low - ESR tantalum or
POS capacitors will be sufficient to provide
adequate ripple voltage filtering at the input of the
converter. However, very low ESR ceramic
capacitors 47 μ F-100 μ F are recommended at the
input of the converter in order to minimize the
input ripple voltage. They should be placed as
close as possible to the input pins of the converter.
YNS12S16 has been designed for stable
operation with no external capacitance as well with
external capacitance. Low ESR ceramic
capacitors placed as close as possible to the load
(Min 47 μ F) are recommended for improved
transient performance and lower output voltage
ripple.
It is important to keep low resistance and low
inductance PCB traces for connecting load to the
output pins of the converter in order to maintain
good load regulation.
ON/OFF (Pin 1)
The ON/OFF pin is used to turn the power
converter on or off remotely via a system signal.
There are two remote control options available,
positive logic (standard option) and negative logic,
and both are referenced to GND. Typical
connections are shown in Fig. A.
The positive logic version turns the converter on
when the ON/OFF pin is at a logic high or left
open, and turns the converter off when at a logic
low or shorted to GND.
CONTROL
INPUT
R* is for negative logic option only
Fig. A: Circuit configuration for ON/OFF function.
The negative logic version turns the converter on
when the ON/OFF pin is at logic low or left open,
and turns the converter off when the ON/OFF pin
is at a logic high or connected to Vin.
ON/OFF pin is internally pulled-up to Vin for a
positive logic version, and pulled-down for a
negative logic version. A TTL or CMOS logic gate,
open collector (open drain) transistor can be used
to drive ON/OFF pin. When using open collector
(open drain) transistor with a negative logic option,
add a pull-up resistor (R*) of 75K to Vin as shown
in Fig. A; This device must be capable of:
- sinking up to 0.2 mA at a low level voltage of
? 0.8 V
- sourcing up to 0.25 mA at a high logic level of
2.3V – 5V
- sourcing up to 0.75 mA when connected to Vin.
Remote Sense (Pin 2)
The remote sense feature of the converter
compensates for voltage drops occurring only
between Vout pin (Pin 4) of the converter and the
load. The SENSE (Pin 2) pin should be connected
at the load or at the point where regulation is
required (see Fig. B). There is no sense feature on
the output GND return pin, where the solid ground
plane should provide low voltage drop.
If remote sensing is not required, the SENSE pin
must be connected to the Vout pin (Pin 4) to
ensure the converter will regulate at the specified
output voltage. If these connections are not made,
the converter will deliver an output voltage that is
slightly higher than the specified value.
MCD10196 Rev. 1.0, 21-Jun-10
Page 5 of 27
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| EBC05DRTS | CONN EDGECARD 10POS DIP .100 SLD |
| VE-B0B-CY-F4 | CONVERTER MOD DC/DC 95V 50W |
| TAJS155M025RNJ | CAP TANT 1.5UF 25V 20% 1206 |
| TAP476K006BRW | CAP TANT 47UF 6.3V 10% RADIAL |
| VE-BT0-CY-F2 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| YS12S16-0G-Q | 功能描述:DC/DC CONVERTER 0.7525-5.5V 88W 制造商:bel power solutions 系列:Y 包装:剪切带（CT） 零件状态:停产 类型:非隔离 PoL 模块 输出数:1 电压 - 输入（最小值）:9.6V 电压 - 输入（最大值）:14V 电压 - 输出 1:0.7525 ~ 5.5 V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:16A 功率（W） - 制造系列:88W 电压 - 隔离:- 应用:ITE（商业） 特性:远程开/关，OCP，OTP，UVLO 安装类型:表面贴装 封装/外壳:6-SMD 模块 大小/尺寸:1.30" 长 x 0.53" 宽 x 0.33" 高（33.0mm x 13.5mm x 8.3mm） 工作温度:-40°C ~ 85°C 效率:94.8% 功率（W） - 最大值:88W 标准包装:1 |
| YS12S16-DG | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YS130101P14B | 制造商:n/a 功能描述:Power SCR |
| YS130101P18C | 制造商:n/a 功能描述:_ |
| YS130101UHP18C | 制造商:n/a 功能描述:_ |
发布紧急采购，3分钟左右您将得到回复。