- 您现在的位置：买卖IC网 > PDF目录19639 > YS12S16-0G (Power-One)CONVERTER DC-DC 12V 16A SMD PDF资料下载
参数资料
| 型号： | YS12S16-0G |
| 厂商： | Power-One |
| 文件页数： | 8/27页 |
| 文件大小： | 0K |
| 描述： | CONVERTER DC-DC 12V 16A SMD |
| 标准包装： | 1 |
| 系列： | Y |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 9.6V |
| 电压 - 输入（最大）： | 14V |
| Voltage - Output 1： | 0.75 ~ 5.5 V |
| 电流 - 输出（最大）： | 16A |
| 电源（瓦） - 制造商系列： | 88W |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-DIP SMD 模块 |
| 尺寸/尺寸： | 1.30" L x 0.53" W x 0.31" H（33.0mm x 13.5mm x 7.9mm） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 94.8% |
| 电源（瓦特）- 最大： | 88W |
| 产品目录页面： | 2739 (CN2011-ZH PDF) |
| 其它名称： | 179-2368-6 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
YNS12S16 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 16 A
All measurements requiring airflow were made in
vertical and horizontal wind tunnel facilities using
Infrared (IR) thermography and thermocouples for
thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining
high reliability. If one anticipates operating the
converter at or close to the maximum loads
specified in the derating curves, it is prudent to
check actual operating temperatures in the
application. Thermographic imaging is preferable;
Fig. D: Location of the thermocouple for thermal testing.
if this capability is
not available, then
thermocouples may be used. di/dt recommends
the use of AWG #40 gauge thermocouples to
ensure measurement accuracy. Careful routing of
the thermocouple leads will further minimize
measurement error. Refer to Fig. D for optimum
measuring thermocouple location.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Figs. x.1 for maximum
temperature of 120 °C. Ambient temperature was
varied between 25 °C and 85 °C, with airflow rates
from 30 to 500 LFM (0.15m/s to 2.5 m/s), and
vertical converter mounting. The airflow during the
testing is parallel to the short axis of the converter,
going from pin 1 and pin 6 to pins 2 – 5.
For each set of conditions, the maximum load
current was defined as the lowest of:
(i) The output current at which either any MOSFET
temperature did not exceed a maximum specified
temperature (120°C) as indicated by the
Efficiency
Figure x.2 shows the efficiency vs. load current
plot for ambient temperature of 25 oC, airflow rate
of 200 LFM (1 m/s) and input voltages of 9.6 V,
12 V, and 14 V.
Power Dissipation
Fig. x.3 shows the power dissipation vs. load
current plot for Ta = 25 oC, airflow rate of 200 LFM
(1 m/s) with vertical mounting and input voltages
of 9.6 V, 12 V, and 14 V.
Ripple and Noise
The output voltage ripple waveform is measured at
full rated load current. Note that all output voltage
waveforms are measured across a 1 ? F ceramic
capacitor.
The output voltage ripple and input reflected ripple
current waveforms are obtained using the test
setup shown in Fig. E.
i S i C
Nex - s Series
thermographic image, or
(ii) The maximum current rating of the converter
(16 A)
1 ? H
source
inductance
V source
C IN
4x47 ? F
ceramic
capacitor
TM
DC/DC
Converter
1 ? F
ceramic
capacitor
C O
100 ? F
ceramic
capacitor
Vout
During normal operation, derating curves with
maximum FET temperature less than or equal to
120 °C should not be exceeded. Temperature on
the PCB at the thermocouple location shown in
Fig. D should not exceed 120 °C in order to
operate inside the derating curves.
Fig. E: Test Setup for measuring input reflected ripple
currents, i s and i c and output voltage ripple.
MCD10196 Rev. 1.0, 21-Jun-10
Page 8 of 27
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| EBC05DRTS | CONN EDGECARD 10POS DIP .100 SLD |
| VE-B0B-CY-F4 | CONVERTER MOD DC/DC 95V 50W |
| TAJS155M025RNJ | CAP TANT 1.5UF 25V 20% 1206 |
| TAP476K006BRW | CAP TANT 47UF 6.3V 10% RADIAL |
| VE-BT0-CY-F2 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| YS12S16-0G-Q | 功能描述:DC/DC CONVERTER 0.7525-5.5V 88W 制造商:bel power solutions 系列:Y 包装:剪切带（CT） 零件状态:停产 类型:非隔离 PoL 模块 输出数:1 电压 - 输入（最小值）:9.6V 电压 - 输入（最大值）:14V 电压 - 输出 1:0.7525 ~ 5.5 V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:16A 功率（W） - 制造系列:88W 电压 - 隔离:- 应用:ITE（商业） 特性:远程开/关，OCP，OTP，UVLO 安装类型:表面贴装 封装/外壳:6-SMD 模块 大小/尺寸:1.30" 长 x 0.53" 宽 x 0.33" 高（33.0mm x 13.5mm x 8.3mm） 工作温度:-40°C ~ 85°C 效率:94.8% 功率（W） - 最大值:88W 标准包装:1 |
| YS12S16-DG | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YS130101P14B | 制造商:n/a 功能描述:Power SCR |
| YS130101P18C | 制造商:n/a 功能描述:_ |
| YS130101UHP18C | 制造商:n/a 功能描述:_ |
发布紧急采购，3分钟左右您将得到回复。