参数资料
型号: YS12S16-0G
厂商: POWER-ONE INC
元件分类: 电源模块
英文描述: 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封装: ROHS COMPLIANT, ZMA-6
文件页数: 24/27页
文件大小: 407K
代理商: YS12S16-0G
OCT 18, 2006 revised to DEC 05, 2006
Page 6 of 27
www.power-one.com
YS12S16 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 16A
Vin
Rw
Rload
Vin
GND
ON/OFF
(Top View)
Converter
TRIM
SENSE
Vout
Y-Series
Fig. B: Remote sense circuit configuration.
Because the sense lead carries minimal current,
large trace on the end-user board are not required.
However, sense trace should be located close to a
ground plane to minimize system noise and insure
optimum performance.
When utilizing the remote sense feature, care must
be taken not to exceed the maximum allowable
output power capability of the converter, equal to the
product of the nominal output voltage and the
allowable output current for the given conditions.
When using remote sense, the output voltage at the
converter can be increased up to 0.5 V above the
nominal rating in order to maintain the required
voltage across the load. Therefore, the designer
must, if necessary, decrease the maximum current
(originally obtained from the derating curves) by the
same percentage to ensure the converter’s actual
output power remains at or below the maximum
allowable output power.
Output Voltage Programming (Pin 3)
The output voltage can be programmed from
0.7525 V to 5.5 V by connecting an external resistor
between TRIM pin (Pin 3) and GND pin (Pin 5); see
Fig. C.
A trim resistor, RTRIM, for a desired output voltage
can be calculated using the following equation:
1
0.7525)
-
(V
5
.
10
R
REQ
-
O
RIM
T
=
[k
Ω]
where,
=
TRIM
R
Required value of trim resistor [k
Ω]
=
REQ
O
V
Desired (trimmed) output voltage [V]
Vin
RTRIM
Rload
Converter
Vin
GND
ON/OFF
(Top View)
TRIM
Vout
SENSE
Y-Series
Fig. C: Configuration for programming output voltage.
Note that the tolerance of a trim resistor directly
affects
the
output
voltage
tolerance.
It
is
recommended to use standard 1% or 0.5% resistors;
for tighter tolerance, two resistors in parallel are
recommended rather than one standard value from
Table 1.
Ground pin of the trim resistor should be connected
directly to the converter GND pin (Pin 5) with no
voltage drop in between. Table 1 provides the trim
resistor values for popular output voltages.
Table 1: Trim Resistor Value
V0-REG [V]
RTRIM [k]
The Closest
Standard Value [k]
0.7525
open
1.0
41.42
41.2
1.2
22.46
22.6
1.5
13.05
13.0
1.8
9.02
9.09
2.0
7.42
7.50
2.5
5.01
4.99
3.3
3.12
3.09
5.0
1.47
5.5
1.21
The output voltage can be also programmed by
external voltage source. To make trimming less
sensitive, a series external resistor Rext is
recommended between TRIM pin and programming
voltage source. Control Voltage can be calculated by
the formula:
15
0.7525)
-
)(V
R
1
(
7
.
0
V
REQ
-
O
EXT
CTRL
+
=
[V]
where,
=
CTRL
V
Control voltage [V]
相关PDF资料
PDF描述
YS12S16-0 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
YS12S16-DG 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
YS12S16-D 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
YSF224B-D DSP-DIGITAL FILTER, PDIP16
YSF224B-M DSP-DIGITAL FILTER, PDSO16
相关代理商/技术参数
参数描述
YS12S16-0G-Q 功能描述:DC/DC CONVERTER 0.7525-5.5V 88W 制造商:bel power solutions 系列:Y 包装:剪切带(CT) 零件状态:停产 类型:非隔离 PoL 模块 输出数:1 电压 - 输入(最小值):9.6V 电压 - 输入(最大值):14V 电压 - 输出 1:0.7525 ~ 5.5 V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出(最大值):16A 功率(W) - 制造系列:88W 电压 - 隔离:- 应用:ITE(商业) 特性:远程开/关,OCP,OTP,UVLO 安装类型:表面贴装 封装/外壳:6-SMD 模块 大小/尺寸:1.30" 长 x 0.53" 宽 x 0.33" 高(33.0mm x 13.5mm x 8.3mm) 工作温度:-40°C ~ 85°C 效率:94.8% 功率(W) - 最大值:88W 标准包装:1
YS12S16-DG 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
YS130101P14B 制造商:n/a 功能描述:Power SCR
YS130101P18C 制造商:n/a 功能描述:_
YS130101UHP18C 制造商:n/a 功能描述:_