- 您现在的位置：买卖IC网 > Datasheet目录537 > ZALM-301-1C-B (CEL)RF TRANSCEIVER 100MW MMCX W/CONN Datasheet资料下载
参数资料
| 型号： | ZALM-301-1C-B |
| 厂商： | CEL |
| 文件页数： | 15/19页 |
| 文件大小： | 0K |
| 描述： | RF TRANSCEIVER 100MW MMCX W/CONN |
| 标准包装： | 32 |
| 系列： | Apex |
| 频率： | 2.4GHz |
| 数据传输率 - 最大： | 250kbps |
| 调制或协议： | 802.15.4 Zigbee |
| 应用： | AMR，ISM，ZigBee? |
| 功率 - 输出： | 100mW（20dBm） |
| 灵敏度： | -96dBm |
| 电源电压： | 2.1 V ~ 3.6 V |
| 电流 - 接收： | 37mA |
| 电流 - 传输： | 170mA |
| 数据接口： | * |
| 天线连接器： | * |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 模块 |
| 包装： | 托盘 |
ZALM-300 Series
PROCESSING
Recommended Reflow Profile
Parameters Values
Ramp up rate (from Tsoakmax to Tpeak)
Minimum Soak Temperature
Maximum Soak Temperature
Soak Time
TLiquidus
Time above TL
Tpeak
Time within 5o of Tpeak
Time from 25o to Tpeak
Ramp down rate
3o/sec max
150oC
200oC
60-120 sec
217oC
60-150 sec
260 + 0oC
20-30 sec
8 min max
6oC/sec max
Achieve the brightest possible solder fillets with a good shape and low contact angle.
Pb-Free Soldering Paste
Use of “No Clean” soldering paste is strongly recommended, as it does not require cleaning after the soldering process.
Note: The quality of the solder joints on the castellations (‘half vias’) where they contact the host board should meet the appropriate
IPC specification. See IPC-A-610-D Acceptability of Electronic Assemblies, section 8.2.4 Castellated Terminations.
Cleaning
In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed
with any cleaning process.
?
?
?
Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and
the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between
neighboring pads. Water could also damage any stickers or labels.
Cleaning with alcohol or a similar organic solvent will likely flood soldering flux residuals into the two housings, which is
not accessible for post-washing inspection. The solvent could also damage any stickers or labels.
Ultrasonic cleaning could damage the module permanently.
The best approach is to consider using a “no clean” soldering paste and eliminate the post-soldering cleaning step.
Optical Inspection
After soldering the Module to the host board, consider optical inspection to check the following:
?
?
?
Proper alignment and centering of the module over the pads.
Proper solder joints on all pads.
Excessive solder or contacts to neighboring pads, or vias.
相关PDF资料 |
PDF描述 |
|---|---|
| ZCH-101-J | LED LIGHT BAR STRIP WIRE HARNESS |
| ZCH-200-J | LED LIGHT BAR STRIP WIRE HARNESS |
| ZFSM-101-KIT-1 | KIT DEVELOPMENT FOR FREESTAR |
| ZIC2410USB-WNA-1 | MODULE 802.15.4 ZIGBEE |
| ZICM0900P2-1C | MESHCONNECT MODULE 1/4 WAVE WIRE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZALVB1 | 制造商:Schneider Electric 功能描述:CONT. BOX LIGHT UNITE, ZALVB1 制造商:Schneider Electric 功能描述:White Light Block For Head 22 Integral LED 24V |
| ZALVB3 | 制造商:Schneider Electric 功能描述:LIGHT MODULE W/PROTECTED LED 24V GREEN 制造商:Schneider Electric 功能描述:Green LED pilot light,24Vdc 制造商:SCHNEIDER ELECTRIC 功能描述:Switch Access Light Block |
| ZALVB4 | 制造商:Schneider Electric 功能描述:LIGHT MODULE W/PROTECTED LED 24V RED 制造商:Schneider Electric 功能描述:Red LED pilot light,24Vdc 制造商:SCHNEIDER ELECTRIC 功能描述:RED LIGHT BLOCK |
| ZALVB5 | 制造商:Schneider Electric 功能描述:LIGHT MODULE W/PROTECTED LED 24V YELLOW 制造商:Schneider Electric 功能描述:Yellow LED pilot light,24Vdc 制造商:SCHNEIDER ELECTRIC 功能描述:ORANGE LIGHT BLOCK |
| ZALVB6 | 制造商:Schneider Electric 功能描述:LIGHT MODULE W/PROTECTED LED 24V BLUE 制造商:Schneider Electric 功能描述:24V LED CONT. BOX LIGHT U 制造商:SCHNEIDER ELECTRIC 功能描述:Switch Access Light Block 制造商:SCHNEIDER ELECTRIC 功能描述:Blue Light Block For Head 22 Integral LED 24V |
发布紧急采购，3分钟左右您将得到回复。