- 您现在的位置：买卖IC网 > PDF目录17644 > ZL2004ALNFT1 (Intersil)IC REG CTRLR BUCK SYNC ADJ 32QFN PDF资料下载
参数资料
| 型号： | ZL2004ALNFT1 |
| 厂商： | Intersil |
| 文件页数： | 11/42页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK SYNC ADJ 32QFN |
| 标准包装： | 1,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | * |
| 占空比： | 95% |
| 电源电压： | 4.5 V ~ 14 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | * |
| 包装： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
ZL2004
and adaptive frequency are available to provide greater
Table 5. Multi-mode Pin Configuration
efficiency improvement.
The ZL2004 can also be used with a single-ended
MOSFET driver. Simple parameter changes allow the
device to use a single PWM to drive the logic input of
such drivers. The trade-offs for using this mode may
include reduced efficiency, reduced ramp-up timing
accuracy, and degraded pre-bias protection.
4.3 Power Management Overview
Pin Tied To
LOW
(Logic LOW)
OPEN
(N/C)
HIGH
(Logic HIGH)
Resistor to SGND
Value
< 0.8 VDC
No connection
> 2.0 VDC
Set by resistor value
The ZL2004 incorporates a wide range of configurable
power management features that are simple to
implement with no external components. Additionally,
Logic
high
Open
ZL
Multi-mode Pin
ZL
Multi-mode Pin
the ZL2004 includes circuit protection features that
continuously safeguard the device and load from
damage due to unexpected system faults. The ZL2004
can continuously monitor input voltage, output
Logic
low
Pin-strap
Settings
R SET
Resistor
Settings
voltage/current, internal
temperature, and the
Figure 6. Pin-strap and Resistor Setting Examples
temperature of an external thermal diode. A Power
Good output signal is also included to enable power-on
reset functionality for an external processor.
All power management functions can be configured
or via the I 2 C/SMBus interface. Monitoring parameters
can also be pre-configured to provide alerts for specific
conditions. See Application Note AN33 for more
details on SMBus monitoring.
4.4 Multi-mode Pins
In order to simplify circuit design, the ZL2004
incorporates patented multi-mode pins that allow the
user to easily configure many aspects of the device
with no programming. Most power management
features can be configured using these pins. The multi-
mode pins can respond to four different connections as
shown in Table 5. These pins are sampled when power
is applied or by issuing a PMBus Restore command
(See Application Note AN33).
Pin-strap Settings: This is the simplest implementation
method, as no external components are required. Using
this method, each pin can take on one of three possible
states: LOW, OPEN, or HIGH. These pins can be
connected to the V25 pin for logic HIGH settings as
this pin provides a regulated voltage higher than 2 V.
Using a single pin, one of three settings can be
selected. Using two pins, one of nine settings can be
selected.
11
Resistor Settings: This method allows a greater range
of adjustability when connecting a finite value resistor
(in a specified range) between the multi-mode pin and
SGND. Standard 1% resistor values are used, and only
every fourth E96 resistor value is used so the device
can reliably recognize the value of resistance
connected to the pin while eliminating the error
associated with the resistor accuracy. Up to 31 unique
selections are available using a single resistor.
I 2 C/SMBus Method: Almost any ZL2004 function can
be configured via the I 2 C/SMBus interface using
standard PMBus commands. Additionally, any value
that has been configured using the pin-strap or resistor
setting methods can also be re-configured and/or
verified via the I 2 C/SMBus. See Application Note
AN33 for more details.
The SMBus device address and VOUT_MAX are the
only parameters that must be set by external pins. All
other device parameters can be set via the I 2 C/SMBus.
The device address is set using the SA0 and SA1 pins.
VOUT_MAX is determined as 10% greater than the
voltage set by the V0 and V1 pins.
FN6846.3
February 15, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| SBG3030CT-T | DIODE SCHOTTKY CC 30V 30A D2-PAK |
| FOXSDLF/115-20 | CRYSTAL 11.0592 MHZ 20PF SMD |
| ISL62392CIRTZ-T | IC PWR SUPPLY CTRLR 28TQFN |
| ISL62391CIRTZ-T | IC PWR SUPPLY CTRLR 28TQFN |
| FOXSDLF/036S | CRYSTAL 3.579545 MHZ 18PF SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZL2004ALNFT1-01 | 功能描述:IC REG CTRLR BUCK SYNC ADJ 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ZL2004ALNN | 功能描述:IC REG CTRLR BUCK SYNC ADJ 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ZL2004ALNN-01 | 功能描述:IC REG CTRLR BUCK SYNC ADJ 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ZL2004ALNNT | 功能描述:IC REG CTRLR BUCK SYNC ADJ 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ZL2004ALNNT-01 | 功能描述:IC REG CTRLR BUCK SYNC ADJ 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。