- 您现在的位置：买卖IC网 > Datasheet目录560 > 0621009610 (Molex Inc)TOOL EXTRACTION BACKPLANE Datasheet资料下载
参数资料
| 型号： | 0621009610 |
| 厂商： | Molex Inc |
| 文件页数： | 10/27页 |
| 文件大小： | 0K |
| 描述： | TOOL EXTRACTION BACKPLANE |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062100-9610 62100-9610 621009610 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
I-Trac? Backplane and Daughtercard Tooling
5. If using the support fixture and an appropriate press, seat
the DaughterCard module until there is less than 0.10mm
(.004 in) clearance between the bottom of the plastic
housing and the surface of the printed circuit board.
6. Remove the loaded support pallet from the press.
7. Remove the insertion tool.
PRESS-IN
TOOL
8. Carefully remove the assembled printed circuit board
from the support pallet.
Vertical Power Module Press-In Tooling
CONNECTOR
ASSEMBLY
Figure 2-10
PC BOARD
SUPPORT PALLET
LOCATING
PIN
CAUTION : Vertical Power Module must be installed separately without any Backplane or DaughterCard
assemblies in the combinations.
WITH 62201-95XX
HOLDER
TOOLING
HOLDER
PRESS-IN
TOOL
PRESS-IN
TOOL
M3 SET
SCREW
VERTICAL
PRESS-IN
TOOL
GUIDE SUFACES
ALONE
POWER
MODULE
Figure 2-11
GUIDE SUFACES
POWER
MODULE
PC BOARD
Figure 2-12
VERTICAL
POWER
MODULE
Depending on the number of modules to be installed and/or the press used, this tool can be used as a stand-
alone or with a group of press-in tools, mounted in a 62201-95XX holder (ordered separately). See Figure 2-11.
1. If the tooling holder is being used, slide the insertion modules into the tooling holder in the proper order. The
modules are keyed so that they cannot be put in backwards.
2. Now tighten the M3 set screws against the modules using the following setups:
One (1) set screw against modules under 10mm wide
Two (2) set screws evenly spaced on a 10mm wide power module.
At least three (3) set screws evenly spaced on a 25mm wide power module.
3. Carefully pre-seat, by hand, the vertical power module(s) into the printed circuit board hole pattern. See
Figure 2-12. Make sure the module(s) are oriented properly to the printed circuit board layout.
4. Line-up the Press-In tool so that the guide surfaces on the tool are in line with the sides of the vertical power
module. See Figure 2-11.
Doc. No: TM-622018699
Revision: D
Release Date: 12-05-07
Revision Date: 04-15-10
UNCONTROLLED COPY
Page 10 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| 0621009900 | 2MM W/B HAND TERMINATION TOOL |
| 0622000700 | LFH STICK INSERTION FIXTU |
| 0622004401 | FERRULE DIE FIXTURE |
| 0622004431 | ASSY-FERRULE DIES |
| 0622004441 | DIE FIXTURE W/ DIE SET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0621009620 | 功能描述:DDR4 LATCH OPENING TOOL 制造商:molex, llc 系列:* 零件状态:有效 标准包装:1 |
| 0621009630 | 制造商:Molex 功能描述:PRESS-IN TOOL IMPEL BP 3 PAIR X 8 COLUMN - Bulk |
| 0621009640 | 制造商:Molex 功能描述:PRESS-IN TOOL 4 PAIR X 6 COLUMN IMPEL BP - Bulk |
| 0621009710 | 制造商:Molex 功能描述:IMPEL DC EXTRACTION TOOL 3 X 8 - Bulk |
| 0621009740 | 制造商:Molex 功能描述:IMPEL DC EXTRACTION TOOL 4 X 6 - Bulk |
发布紧急采购，3分钟左右您将得到回复。