- 您现在的位置：买卖IC网 > Datasheet目录560 > 0621009610 (Molex Inc)TOOL EXTRACTION BACKPLANE Datasheet资料下载
参数资料
| 型号： | 0621009610 |
| 厂商： | Molex Inc |
| 文件页数： | 9/27页 |
| 文件大小： | 0K |
| 描述： | TOOL EXTRACTION BACKPLANE |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062100-9610 62100-9610 621009610 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
I-Trac? Backplane and Daughtercard Tooling
3. Locate the tooling assembly in the connector assembly,
carefully checking alignment. The orientation feature on
the tool must engage with the notch on the connector
housing. See Figure 2-7.
4. Position the pre loaded support pallet under the press
platen.
5. Cycle the press. See Section 2.1 (Press Stroke
Adjustment).
6. When using the application tool and an appropriate press,
seat the header assembly until there is less than 0.10mm
(.004 in) clearance between the bottom of the plastic
housing and the surface of the printed circuit board.
7. Remove the loaded support pallet.
8. Carefully remove the insertion tool assembly. Remove the
printed circuit board.
Daughtercard Insertion Tooling
CONNECTOR
HOUSING
ORIENTATION
FEATURE
Figure 2-7
TOOLING LOCATED IN THE
CONNECTOR ASSEMBLY
WITH 62201-95XX
HOLDER
ALONE
SIGNAL MODULE
Figure 2-9
PC BOARD
TYPICAL DAUGHTERCARD
ASSEMBLY ON THE PC BOARD
Figure 2-8
Operation for inserting Daughtercard assemblies is similar to backplanes and can be used alone or stacked in a tool
holder for larger connector assemblies. See Figure 2-8.
1. Locate the Daughtercard connector assembly on the printed circuit board.
2. Pre-seat the assembly into the board by hand. Check for proper seating, without contact pins bending under
the assembly after pre loading on to the Printed circuit board. See Figure 2-9.
3. Locate the printed circuit board with the connector assembly on the user supplied support pallet (Optional).
4. Position the insertion tooling on the connector assembly. See Figure 2-10.Position the printed circuit board under
the press platen (Optional).
CAUTION : To prevent injury, never operate any press without the guards in place. Refer to the press
manufacturer’s instruction manual.
Doc. No: TM-622018699
Revision: D
Release Date: 12-05-07
Revision Date: 04-15-10
UNCONTROLLED COPY
Page 9 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| 0621009900 | 2MM W/B HAND TERMINATION TOOL |
| 0622000700 | LFH STICK INSERTION FIXTU |
| 0622004401 | FERRULE DIE FIXTURE |
| 0622004431 | ASSY-FERRULE DIES |
| 0622004441 | DIE FIXTURE W/ DIE SET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0621009620 | 功能描述:DDR4 LATCH OPENING TOOL 制造商:molex, llc 系列:* 零件状态:有效 标准包装:1 |
| 0621009630 | 制造商:Molex 功能描述:PRESS-IN TOOL IMPEL BP 3 PAIR X 8 COLUMN - Bulk |
| 0621009640 | 制造商:Molex 功能描述:PRESS-IN TOOL 4 PAIR X 6 COLUMN IMPEL BP - Bulk |
| 0621009710 | 制造商:Molex 功能描述:IMPEL DC EXTRACTION TOOL 3 X 8 - Bulk |
| 0621009740 | 制造商:Molex 功能描述:IMPEL DC EXTRACTION TOOL 4 X 6 - Bulk |
发布紧急采购，3分钟左右您将得到回复。