- 您现在的位置：买卖IC网 > Datasheet目录560 > 0621009610 (Molex Inc)TOOL EXTRACTION BACKPLANE Datasheet资料下载
参数资料
| 型号： | 0621009610 |
| 厂商： | Molex Inc |
| 文件页数： | 7/27页 |
| 文件大小： | 0K |
| 描述： | TOOL EXTRACTION BACKPLANE |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062100-9610 62100-9610 621009610 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
I-Trac? Backplane and Daughtercard Tooling
2
Installation and Operation
2.1 Printed Circuit Board Support
The I-Trac? tooling requires up to 4 lb. per pin of force to press the connectors into the printed circuit boards.
Therefore, a backup or support is suggested to prevent damage to the printed circuit board. The support fixture
should have clearance for the connector terminals when they protrude through the underside of the printed circuit
board. It is also recommended that the support fixture have locating pins. Due to the custom nature of each
application, Molex does not supply support and locating fixtures. The customer normally supplies these to fit their
individual needs.
The following is one simple way of making a printed circuit board support and locating fixture:
1. Locate a suitable piece of material for the backup. It should be approximately 3/4 inch thick and same size or
a little larger than the printed circuit board to be used. While aluminum could be used, a rigid nonconductive
material such as a phenolic is preferred. (A stack of scrap printed circuit boards of suitable size could be
fastened together and used.)
2. Obtain a scrap printed circuit board like the ones to be assembled. Attach this board to the material from step
1.
3. Using an oversize drill bit, drill through each hole where a pin from the connector will go. Drill deep enough
into the lower material to be certain the pins do not bottom out when inserted (at least 5.0mm (0.20”) deep).
4. Locate two (2) holes on the printed circuit board to use as locating points. Drill for and mount suitably sized
dowel pins in these two locations on the support fixture.
5. Clear out the support for any components mounted on the underside of the printed circuit board.
6 Place a printed circuit board on top of the support, located by the two pins, and check that the holes for the
connector pins are aligned.
7. Pre-insert a connector in the printed circuit board in the correct position.
8. Insert the press-in tool of proper size into the connector.
9. Place the support with the printed circuit board under the press ram.
10. Press the connector into the printed circuit board and observe for any deflection of the board when the ram is
at the bottom of its stroke.
0.10mm
2.2 Press Stroke Adjustment
Most presses have some means of adjusting the stroke, please refer to the
appropriate manual (for the press being used) for press stroke adjustments.
The stroke should be adjusted so that when the press ram stops in the
down position, the bottom of the connector is flush to 0.10mm (.004”) above
the surface of the Printed circuit board. See Figure 2-1.
(.004 in.)
Max.
Figure 2-1
MAXIMUM CLEARANCE WHEN
CONNECTOR FULLY SEATED
2.3 Installation
The only installation required is when you need to install insertion modules into a tooling holder. To do this, use
the following procedure:
Doc. No: TM-622018699
Revision: D
Release Date: 12-05-07
Revision Date: 04-15-10
UNCONTROLLED COPY
Page 7 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| 0621009900 | 2MM W/B HAND TERMINATION TOOL |
| 0622000700 | LFH STICK INSERTION FIXTU |
| 0622004401 | FERRULE DIE FIXTURE |
| 0622004431 | ASSY-FERRULE DIES |
| 0622004441 | DIE FIXTURE W/ DIE SET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0621009620 | 功能描述:DDR4 LATCH OPENING TOOL 制造商:molex, llc 系列:* 零件状态:有效 标准包装:1 |
| 0621009630 | 制造商:Molex 功能描述:PRESS-IN TOOL IMPEL BP 3 PAIR X 8 COLUMN - Bulk |
| 0621009640 | 制造商:Molex 功能描述:PRESS-IN TOOL 4 PAIR X 6 COLUMN IMPEL BP - Bulk |
| 0621009710 | 制造商:Molex 功能描述:IMPEL DC EXTRACTION TOOL 3 X 8 - Bulk |
| 0621009740 | 制造商:Molex 功能描述:IMPEL DC EXTRACTION TOOL 4 X 6 - Bulk |
发布紧急采购，3分钟左右您将得到回复。