- 您现在的位置：买卖IC网 > Datasheet目录542 > 1-46673-0 (TE Connectivity)TOOL HEAD CRIMP 22-16AWG STRATO Datasheet资料下载
参数资料
| 型号： | 1-46673-0 |
| 厂商： | TE Connectivity |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD CRIMP 22-16AWG STRATO |
| 标准包装： | 1 |
| 系列： | Strato-Therm |
| 压接或电缆尺寸： | 16-22 AWG |
| 压接手柄： | 1213563-1，1213804 |
| 连接器类型： | 端子及连接件 |
| 相关产品： | 1213563-1-ND - TOOL DAHT ADAPTER ASSEMBLY |
STRATO- THERM Crimping Heads
6.3. Visual Inspection
1. Remove all lubrication and accumulated film by
immersing the crimping head in a suitable
commercial degreaser that will not affect paint or
plastic.
408- 10033
Suggested Plug Gage Design for
Insulation Barrel Section of Crimping Chamber
GO Dim. NO-- GO Dim.
2. Make certain all components are in place. If
replacements are necessary, refer to Figure 10.
3. Check all bearing surfaces for wear. Replace
worn parts.
4. Inspect crimp area for flattened, chipped, or
broken areas. Replace worn or damaged parts.
“W”
Jaw Closure
Configuration
GO
6.35 [.250]
Min Typ
NO
GO
“W”
GO
NO-- GO
3.05
6.4. Lubrication
Lubricate all pins, pivot points, and bearing surfaces
with a high quality grease. Tyco Electronics
recommends the use of Molykote grease, which is a
commercially available lubricant. Lubricate according
to the following schedule:
Head used in daily production -- lubricate daily
Head used daily (occasional) -- lubricate weekly
Head used weekly -- lubricate monthly
Wipe excess grease from crimping head, particularly
from jaw closure areas. Grease transferred from jaw
closure area onto certain terminations may affect the
electrical characteristics of an application.
HAND
TOOL
1--46673--0
1--46673--1
1--46988--0
DANGER
GAGE ELEMENT DIMENSIONS
“W” (Width)
(Max)
0.762--0.770 1.267--1.270
[.0300--.0303] [.0499--.0500]
1.016--1.024 1.521--1.524 [.120]
[.0400--.0403] [.0599--.0600]
Figure 8 (end)
Disconnect the battery and remove crimping
head from tool before inspecting crimping
chambers.
6.5. Gaging the Crimping Chamber
This inspection requires the use of plug gages
conforming to the dimensions shown in Figure 8. Tyco
Electronics does not manufacture or market these
gages.
Suggested Plug Gage Design for
Wire Barrel Section of Crimping Chamber
GO NO-- GO
Dim. Dim.
1. Remove oil and dirt from the jaw bottoming
surfaces and plug gage element surfaces.
2. Close wire barrel crimping jaws until they are
bottomed, but not under pressure.
3. Align GO element with wire barrel crimping
section. Push element straight into crimping
chamber without using force. The GO element
must pass completely through the chamber as
shown in Figure 9.
“R”
Jaw Closure
Configuration
6.35 [.250]
Min Typ
50.8 [2.00]
Min Typ
“R”
4. Align the NO--GO element and try to insert it
into the chamber. The element may start entry, but
it must not pass completely through the crimping
chamber.
5. Repeat this procedure for the insulation crimping
section using a plug gage as shown in Figure 8.
GO
NO-- GO
1.57
HAND
TOOL
1--46673--0
1--46673--1
1--46988--0
GAGE ELEMENT DIMENSIONS
“R”
(Radius)
1.499--1.506 1.648--1.651
[.0590--.0593] [.0649--.0650]
1.702--1.709 1.851--1.854 [.062]
[.0670--.0673] [.0729--.0730]
Figure 8 (cont’d)
If the crimping chamber passes the gage inspection,
the crimping head is considered dimensionally correct
and should be lubricated with a THIN coat of any
good SAE 20 motor oil. If the crimping chamber does
not conform to the plug gage conditions, contact your
local Tyco Electronics Field Representative or refer to
Section 7, REPLACEMENT AND REPAIR.
For additional information about the use of a plug
gage, see Instruction Sheet 408--7424.
Rev B
Tyco Electronics Corporation
5 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 1-47387-0 | TOOL HEAD CRIMP 16-14AWG PIDG |
| 1-49935-0 | TOOL HEAD CRIMP 22-10AWG SOLIS |
| 0010844061 | 084 DIA ASSY HDR HSG PIN 94V-0 |
| 0011020001 | INSERTION TOOL HT1807 |
| 0011020003 | INSERTION TOOL HT1353 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-46673-1 | 功能描述:手工工具 DA BAT TL HD 22-16 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 146675 | 制造商:Molex 功能描述: |
| 146681-000 | 制造商:TE Connectivity 功能描述:TXR54AB45-2210AI - Bulk 制造商:TE Connectivity 功能描述:ADPTR TINEL LOCK ANG SHELL 22 制造商:TE Connectivity 功能描述:Connector Accessories Tinel Lock Adapter 45? Angle Aluminum Alloy Olive Drab Cadmium Over Electroless Nickel |
| 1466924-1 | 制造商:TE Connectivity 功能描述: |
| 1466A 0107500 | 功能描述:CBL 4PR/18AWG 1COND/22AWG SHLD 制造商:belden inc. 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。