参数资料
| 型号： | 101-0411 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 20/90页 |
| 文件大小： | 0K |
| 描述： | INTERFACE 12KEYDISP ETHNT OP6700 |
| 标准包装： | 25 |
| 系列： | SBC |
| 模块/板类型： | 单板计算机模块 |
| 适用于相关产品： | OP6700 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页
User’s Manual
23
3.2.1 RS-232
The Intellicom’s RS-232 serial channel is connected to an RS-232 transceiver, U11. U11
provides the voltage output, slew rate, and input voltage immunity required to meet the
RS-232 serial communication protocol. Basically, the chip translates the Rabbit 2000’s 0
V to +Vcc signals to RS-232 signal levels. Note that the polarity is reversed in an RS-232
circuit so that +5 V is output as approximately -10 V and 0 V is output as approximately
+10 V. U11 also provides the proper line loading for reliable communication.
The maximum baud rate is 115,200 bps. RS-232 can be used effectively at this baud rate
for distances up to 15 m.
3.2.2 RS-485
The Intellicom has one RS-485 serial channel, which is connected to the Rabbit 2000
serial port B through U10, an RS-485 transceiver. The chip’s slew rate limiters provide for
a maximum baud rate of 250,000 bps, which allows for a network of up to 1200 m (or
4000 ft). The half-duplex communication uses the Rabbit 2000’s PC0 pin to control the
data enable on the communication line.
The RS-485 signals are available on pins 3 and 4 of header J7, and on J5, the RJ-12 jack.
The Intellicom can be used in an RS-485 multidrop network. Connect the 485+ to 485+
and 485– to 485– using single twisted-pair wires (nonstranded, tinned) as shown in
Alternatively, the RS-485 multidrop network may be hooked up using cables with RJ-12
plugs. Note that the RJ-12 jack has +RAW_485 and GND, which means that only one
Intellicom needs to be connected to an external power source via an AC adapter. When
doing so, ensure that the AC adapter has sufficient capacity for the network — each Intel-
licom unit nominally draws 100 mA at 24 VDC.
CAUTION: If you plan to connect a power supply to more than one
Intellicom unit
in an RS-485 network using the RJ-12 jacks, rework the RS-485 cables so they do not
connect +RAW_RS485 through the RJ-12 jack to the boards in the network.
NOTE: The RS-485 port is available only in the factory default configuration. The RS-485
port will not be available when you select the configuration option for both 3-wire
RS-232 ports or one 5-wire RS-232 port.
相关PDF资料 |
PDF描述 |
|---|---|
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
| 25FMN-BMT-A-TF | CONN FMN HSNG 25POS SNGL NOR SMD |
| 046239012001800+ | CONN FPC ONE-TOUCH LCK .5MM 12 |
| AT24C01-10PI-1.8 | IC EEPROM 1KBIT 400KHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 10104110 | 制造商:FCI-CONNECTOR 制造商全称:FCI connector 功能描述:MICRO USB B TYPE RECEPTACLE |
| 10104110-0001LF | 功能描述:USB接头 5P Quick Connect Micro USB TypeB Rcpt RoHS:否 制造商:FCI 产品:USB Type A Connectors 标准:USB 3.0 端口数量: 位置/触点数量:9 型式:Female 电流额定值:1.8 A 安装风格:Through Hole 端接类型:Solder Pin 连接器类型:USB 3.0 Receptacle |
| 10104110-0001LF | 制造商:FCI 功能描述:MICRO USB B, RECEPTACLE, 5POS, SMT RT AN |
| 10-104-11-01 | 制造商:Concord Electronics Inc 功能描述:Contact Solder ST Thru-Hole |
| 10-104-11-03 | 制造商:Concord Electronics Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。