参数资料
| 型号： | 101-0411 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 51/90页 |
| 文件大小： | 0K |
| 描述： | INTERFACE 12KEYDISP ETHNT OP6700 |
| 标准包装： | 25 |
| 系列： | SBC |
| 模块/板类型： | 单板计算机模块 |
| 适用于相关产品： | OP6700 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页
User’s Manual
51
5.5 Run the PINGME.C Demo
In order to run this program, edit the IP address and netmask in the PINGME.C program
(SAMPLES\TCPIP\ICMP) to the values given above (10.1.1.2 and 255.255.255.248).
Compile the program and start it running under Dynamic C. The crossover cable is con-
nected from your computer’s Ethernet adapter to the Intellicom board’s RJ-45 Ethernet
connector. When the program starts running, the green LNK light on the Intellicom board
should be on to indicate an Ethernet connection is made. (Note: If the LNK light does not
light, you may not have a crossover cable, or if you are using a hub perhaps the power is
off on the hub.)
The next step is to ping the board from your PC. This can be done by bringing up the MS-DOS
window and running the pingme program:
ping 10.1.1.2
or by Start > Run
and typing the entry
ping 10.1.1.2
Notice that the red ACT light flashes on the Intellicom board while the ping is taking
place, and indicates the transfer of data. The ping routine will ping the board four times
and write a summary message on the screen describing the operation.
5.6 Running More Demo Programs With a Direct Connection
The programs STATIC.C and SSI3.C (SAMPLES\TCPIP\HTTP) demonstrate how to
make the Intellicom board be a Web server. This program allows you to turn the LEDs on
an attached Demonstration Board from the Development Kit on and off from a remote
Web browser. In order to run these sample programs, edit the IP address as for the pingme
program, compile the program and start it executing. Then bring up your Web browser and
enter the following server address: http://10.1.1.2.
This should bring up the Web page served by the sample program.
The sample program RXSAMPLE.C (SAMPLES\TELNET) allows you to communicate with
the Intellicom board using the Telnet protocol. To run this program, edit the IP address,
compile the program, and start it running. Run the Telnet program on your PC (Start >
Run telnet 10.1.1.2
). Each character you type will be printed in Dynamic C's STDIO
window, indicating that the board is receiving the characters typed via TCP/IP.
相关PDF资料 |
PDF描述 |
|---|---|
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
| 25FMN-BMT-A-TF | CONN FMN HSNG 25POS SNGL NOR SMD |
| 046239012001800+ | CONN FPC ONE-TOUCH LCK .5MM 12 |
| AT24C01-10PI-1.8 | IC EEPROM 1KBIT 400KHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 10104110 | 制造商:FCI-CONNECTOR 制造商全称:FCI connector 功能描述:MICRO USB B TYPE RECEPTACLE |
| 10104110-0001LF | 功能描述:USB接头 5P Quick Connect Micro USB TypeB Rcpt RoHS:否 制造商:FCI 产品:USB Type A Connectors 标准:USB 3.0 端口数量: 位置/触点数量:9 型式:Female 电流额定值:1.8 A 安装风格:Through Hole 端接类型:Solder Pin 连接器类型:USB 3.0 Receptacle |
| 10104110-0001LF | 制造商:FCI 功能描述:MICRO USB B, RECEPTACLE, 5POS, SMT RT AN |
| 10-104-11-01 | 制造商:Concord Electronics Inc 功能描述:Contact Solder ST Thru-Hole |
| 10-104-11-03 | 制造商:Concord Electronics Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。