参数资料
| 型号： | 101-0558 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 51/94页 |
| 文件大小： | 0K |
| 描述： | COMPUTER SNG BD BL1800 512K SRAM |
| 标准包装： | 10 |
| 系列： | SBC |
| 模块/板类型： | 单板计算机模块 |
| 适用于相关产品： | BL1800 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
User’s Manual
51
4.4 Jackrabbit Function Calls
4.4.1 I/O Drivers
The Jackrabbit contains four high-power digital output channels, two D/A converter out-
put channels, and one A/D converter input channel. These I/O channels can be accessed
using the functions found in the JRIO.LIB library.
4.4.1.1 Initialization
The function jrioInit() must be called before any other function from the JRIO.LIB
library. This function initializes the digital outputs and sets up the driver for the analog
input/outputs. The digital outputs correspond to the Rabbit processor’s port E bits 0–3, and
the analog I/O uses timer B; bits 1, 2, and 4 of port D; and bits 6 and 7 of port E.
The function void jrioInit() initializes the I/O drivers for Jackrabbit. In particular, it
sets up parallel port D bits 1, 2, and 4 for analog output, port E bits 0–3 for digital output,
and starts up the pulse-width modulation routines for the A/D and D/A channels. Note that
these routines can consume up to 20% of the CPU’s processing power; the routines use
timer B and the B1 and B2 match registers.
4.4.1.2 Digital Outputs
The Jackrabbit contains four high-power digital output drivers, HV0–HV3, on header J4.
These can be turned on and off with the following functions from the library JRIO.LIB.
HV0, HV1, and HV2 are open-collector sinking outputs, and are able to sink up to 1 A
(200 mA for the Jackrabbit and BL1820) from a 30 V source connected to the K line on
header J4. HV3 is a sourcing output that is able to source up to 500 mA (100 mA for the
BL1810 and BL1820) from a 30 V source connected to the K line.
CAUTION: Remember to cut the trace
between K and Vcc inside the outline
for header JP2 on the top side of the
Prototyping Board if you are supplying
K from a separate power supply. An
exacto knife, a precision grinder tool,
or a screwdriver may be used to cut
through the traces as shown in
NOTE: Failure to do this could lead to
the destruction of the Rabbit 2000
microprocessor and other components
once the Jackrabbit is connected to the
Prototyping Board.
Figure 16. Cut Trace on Prototyping Board
When Vcc and K Are Different
Cut gray trace
as shown
Cut
Buzzer
Top Side
Prototyping
Board
JP2
1
2
3
R3
R1
LS1
RT
1
BZR
VCC
K
AD0
PE4
POT
HV0 +RAW
COIL(-)
PD0
GND
AD0
+
JP2
K
VCC
相关PDF资料 |
PDF描述 |
|---|---|
| 396-036-526-204 | CARD EDGE 36POS DL .125X.250 BLK |
| 396-036-526-202 | CARD EDGE 36POS DL .125X.250 BLK |
| 101-0411 | INTERFACE 12KEYDISP ETHNT OP6700 |
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 10105584 | 制造商:Amphenol Corporation 功能描述:10-341374-222 - Bulk |
| 101055OO | 制造商:TE Connectivity 功能描述: |
| 101056084S | 制造商:Amphenol Aerospace 功能描述:CONNECTOR |
| 101-0561 | 功能描述:模块化系统 - SOM RCM3400 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 10-105610-02S | 制造商:Amphenol Aerospace 功能描述:PLUG |
发布紧急采购，3分钟左右您将得到回复。