参数资料
| 型号： | 101-0558 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 9/94页 |
| 文件大小： | 0K |
| 描述： | COMPUTER SNG BD BL1800 512K SRAM |
| 标准包装： | 10 |
| 系列： | SBC |
| 模块/板类型： | 单板计算机模块 |
| 适用于相关产品： | BL1800 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
User’s Manual
13
2.4 Run a Sample Program
If you already have Dynamic C installed, you are now ready to test your programming
connections by running a sample program. Start Dynamic C by double-clicking on the
Dynamic C icon on your desktop or in your Start menu. Dynamic C uses the serial port
specified during installation.
If you are using a USB port to connect your computer to the BL1810, click on the Commu-
nications
tab and verify that Use USB to Serial Converter is selected to support the USB
programming cable. Click OK.You may have to determine which COM port was assigned to
the RS-232/USB converter. Open Control Panel > System > Hardware > Device Man-
ager > Ports
and identify which COM port is used for the USB connection. In Dynamic C,
select Options > Project Options, then select this COM port on the Communications
tab, then click OK. You may type the COM port number followed by Enter on your com-
puter keyboard if the COM port number is outside the range on the dropdown menu.
Find the file PONG.C, which is in the Dynamic C SAMPLES folder. To run the program,
open it with the File menu, compile it using the Compile menu, and then run it by selecting
Run
in the Run menu. The STDIO window will open on your PC and will display a small
square bouncing around in a box. This program shows that the CPU is working.
2.4.1 Troubleshooting
If Dynamic C cannot find the target system (error message "No Rabbit Processor
Detected."
):
Check that the BL1810 is powered correctly — the AC adapter should be connected to
header J1 on the Jackrabbit board
and should be plugged in to a wall outlet.
Check both ends of the programming cable to ensure that they are firmly plugged into
the PC and that the PROG connector, not the DIAG connector, is plugged in to the
programming port on the BL1810 with the colored side lined up with pin 1.
Ensure that the BL1810 is firmly and correctly installed in its sockets on the Prototyp-
ing Board.
Select a different COM port within Dynamic C. From the Options menu, select
Project Options
, then select another COM port from the list on the Communications
tab, then click OK. Press <Ctrl-Y> to force Dynamic C to recompile the BIOS.
If a program compiles and loads, but then loses target communication before you can
begin debugging, it is possible that your PC cannot handle the default debugging baud rate.
Try lowering the debugging baud rate as follows.
Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications
menu. Choose a lower debug baud rate, then click OK.
相关PDF资料 |
PDF描述 |
|---|---|
| 396-036-526-204 | CARD EDGE 36POS DL .125X.250 BLK |
| 396-036-526-202 | CARD EDGE 36POS DL .125X.250 BLK |
| 101-0411 | INTERFACE 12KEYDISP ETHNT OP6700 |
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 10105584 | 制造商:Amphenol Corporation 功能描述:10-341374-222 - Bulk |
| 101055OO | 制造商:TE Connectivity 功能描述: |
| 101056084S | 制造商:Amphenol Aerospace 功能描述:CONNECTOR |
| 101-0561 | 功能描述:模块化系统 - SOM RCM3400 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 10-105610-02S | 制造商:Amphenol Aerospace 功能描述:PLUG |
发布紧急采购，3分钟左右您将得到回复。