参数资料
| 型号： | 101-0558 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 6/94页 |
| 文件大小： | 0K |
| 描述： | COMPUTER SNG BD BL1800 512K SRAM |
| 标准包装： | 10 |
| 系列： | SBC |
| 模块/板类型： | 单板计算机模块 |
| 适用于相关产品： | BL1800 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
10
Jackrabbit (BL1800)
2.2.2 Connect Programming Cable
The programming cable connects the Jackrabbit to the PC running Dynamic C to down-
load programs and to monitor the Jackrabbit during debugging.
Connect the 10-pin connector of the programming cable labeled PROG to header J3 on
the Jackrabbit board as shown in Figure 2. Be sure to orient the marked (usually red) edge
of the cable towards pin 1 of the connector. (Do not use the DIAG connector, which is used
for a normal serial connection.)
NOTE: Use only the programming cable that has a red shrink wrap around the RS-232
level converter (Part No. 20-101-0513), which is supplied with the Development Kit.
Other Rabbit programming cables are not voltage-compatible or their connector sizes
may be different.
Figure 2. Power and Programming Cable Connections
to Jackrabbit Board
NOTE: Never disconnect the programming cable by pulling on the ribbon cable.
Carefully pull on the connector to remove it from the header.
Connect the other end of the programming cable to a COM port on your PC.
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use
an RS-232/USB converter (Part No. 20-151-0178) with the programming cable sup-
plied with the Jackrabbit Development Kit. Note that not all RS-232/USB converters
work with Dynamic C.
PROTOTYPING BOARD
JACKRABBIT BOARD
JP1
U4
VIN
GND
RESET
JACKRABBIT Z-World, Inc.
GND
PA0
PA2
PA4
PA6
GND
PB0
PB2
PB4
PB6
WDO
GND
PE6
PE4
PE2
PE0
HV0
HV2
K
GND
VCC
PA1
PA3
PA5
PA7
GND
PB1
PB3
PB5
PB7
PCLK
PE7
PE5
PE3
PE1
GND
HV1
HV3
+RAW
VCC
GND
RXC
TXC
PC1
PC3
PC5
PC7
AGND
DA1
PD1
PD3
PD5
PD7
GND
485+
VCC
SM1
STAT
VBAT
GND
VCC
RXB
TXB
PC0
PC2
PC4
PC6
AD0
DA0
PD0
PD2
PD4
PD6
GND
485
VCC
SM0
IOBEN
GND
/RST
J5
U6
U5
U3
J4
U1
J1
J2
J3
Y3
Rabbit 2000
SRAM
RS-232
RS-485
Colored side
lines up with
pin 1
Remove slot cover,
insert tab into slot
Snap plug into place
2
1
Assemble
AC Adapter
To
PC COM port
PROG
DIAG
Programming
connector
Diagnostic
connector
Red
shrink wrap
相关PDF资料 |
PDF描述 |
|---|---|
| 396-036-526-204 | CARD EDGE 36POS DL .125X.250 BLK |
| 396-036-526-202 | CARD EDGE 36POS DL .125X.250 BLK |
| 101-0411 | INTERFACE 12KEYDISP ETHNT OP6700 |
| AT24C02A-10PI-2.7 | IC EEPROM 2KBIT 400KHZ 8DIP |
| AT24C02A-10PI-1.8 | IC EEPROM 2KBIT 400KHZ 8DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 10105584 | 制造商:Amphenol Corporation 功能描述:10-341374-222 - Bulk |
| 101055OO | 制造商:TE Connectivity 功能描述: |
| 101056084S | 制造商:Amphenol Aerospace 功能描述:CONNECTOR |
| 101-0561 | 功能描述:模块化系统 - SOM RCM3400 RABBITCORE RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 10-105610-02S | 制造商:Amphenol Aerospace 功能描述:PLUG |
发布紧急采购，3分钟左右您将得到回复。