参数资料
| 型号： | 10520 |
| 厂商： | Desco |
| 文件页数： | 5/10页 |
| 文件大小： | 0K |
| 描述： | FINISH FLOOR STATGUARD 55GAL |
| 标准包装： | 1 |
| 系列： | Statguard® |
| 处理剂/清洁剂类型： | 抗静电地板涂层 |
| 使用： | 地板 |
| 技术规格： | 10&sup7; ~ 10&sup9;表面电阻系数 |
| 数量： | 55 加仑 |
| 包装： | 鼓 |
TB-7042 Page 4 of 10
2013 DESCO INDUSTRIES, INC.
Employee Owned
DESCO INDUSTRIES INC.
3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178 Web Site: DescoIndustries.com
2. To damp mop, use a 1 to 3 dilution of Statguard
Floor Finish in water (1 part Statguard to 3 parts
water). Let dry thoroughly. The mop and bucket
should be dedicated to Statguard use only.
MOP and RECOAT PROGRAM
To replenish solids that are worn away over time, a
mop and recoat can be done after cleaning the surface.
This can improve gloss and snap back electrical
properties.
1. Follow the Damp Mop Program to clean the surface
above (do not use the floor cleaner)
2. Pour Statguard Floor Finish (undiluted) into a
clean and dedicated mop bucket and apply a
medium coat with a clean rayon (or cotton blend)
mop using a figure 8 motion.
3. Let the coat dry (at least 60 minutes), then apply a
second coat if needed. Do not use forced air
drying.
FLOOR CLEANER PROGRAM
Statguard Floor Cleaner will clean surface stains
and heel marks. As a cleaner it will reduce the gloss
of the floor. Do not re-apply Statguard finish after
using Statguard Floor Cleaner, see Mop and Recoat
program.
Heavy-Moderate Traffic:
Clean once a week, or as dictated by floor appearance.
Low Traffic Floors:
Clean floors as dictated by floor appearance.
1. Dust mop with untreated mop.
2. Dilute Statguard Dissipative Floor Cleaner 10 parts
clean water to 1 part Floor Cleaner. For example,
use five (5) gallons of clean water to two (2) quarts
of floor cleaner.
3. Damp mop floor with cleaner solution and let
dry thoroughly. The mop and bucket should be
dedicated to Statguard use only.
DRY BURNISH PROGRAM
Heavy-Moderate Traffic:
A dry burnish program will increase gloss and remove
surface imperfections.
Dry burnish once a week or as dictated by floor
appearance.
Low Traffic Floors:
Dry burnish as dictated by floor appearance.
1. Dust mop with an untreated mop.
2. Dry burnish at 1000-2000 rpm.
3. After dry burnish, dry mop the area with an
untreated dry mop if necessary.
FLAT MOP PROGRAM (OPTIONAL)
1. Flat mop can come with a refillable dispenser, that
allows for easier determination of proper amount of
Floor Finish / sq ft. For example, if the floor finish
application rate is 1 gallon / 2000 sq ft, a 32 oz
dispenser holds 500 sq ft of finish.
2. Flat mopping systems reduce workers fatigue as
they are lighter in weight. Roughly three pounds
when wet vs the traditional cotton loop mops which
can weigh eight to ten pounds when wet.
3. The Flat mop with dispenser is faster, as one does
NOT need to constantly “dip the mop and squeeze
out excess”.
4. The flat mop doesn’t hold as much residual finish
as a string mop, so the application of the proper
amount of Floor Finish, is more precise.
Equipment needed:
Clean rayon (or cotton blend) mop, dedicated to
Statguard Floor Finish use only
Bucket dedicated to Statguard Floor Finish use
only.
Flat mop (Optional)
1. Pour Statguard Floor Finish into a clean and
dedicated mop bucket and apply with a clean rayon
(or cotton blend) mop using a figure 8 motion.
2. Let the first coat dry (at least 60 minutes), then
apply a second coat. Do not use force air drying.
3. Let second coat dry for (at least 60 minutes) to
yield a bright gloss. Repeat application to attain
higher gloss and higher conductivity (two coats
will provide acceptable dissipative resistance on
most floors). Keep traffic from the floor for at least
six hours after the last coat is applied. See dry
time recommendations on page 2 in this technical
bulletin.
4. One or preferably two additional coats of floor finish
should be applied if the floor is to be maintained by
dry burnishing or spray buffing.
5. Maintain the polish following the Dust Mop, Damp
Mop, Floor Cleaner, Dry Burnish, or Spray Buff
maintenance procedure below.
Statguard Maintenance
DUST MOP PROGRAM
1. Keep the floor surface clean. Use an untreated dust
mop or push broom nightly or as needed to remove
accumulated dirt and insulative contaminant.
DAMP MOP PROGRAM
1. Keep the floor surface clean. Use an untreated dust
mop or push broom nightly or as needed to remove
accumulated dirt and insulative contaminant.
相关PDF资料 |
PDF描述 |
|---|---|
| 10601 | WIPES ANTISTATC CAN OF 60, 12 CT |
| 12550 | FOAM HIGH DENSITY 3/4" 24X36 |
| 12668 | FOAM LOW DENSITY DISSIPATIVE |
| 12782 | BAG ESD SHIELD 6X10 METAL-IN GRN |
| 13070 | BAG SHIELD METAL-OUT 8X12 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 105-20 | 制造商: 功能描述: 制造商:undefined 功能描述: 制造商:. 功能描述: |
| 1052000000 | 功能描述:2 位 端接块 接头 0.197"（5.00mm） 垂直式 制造商:weidmuller 系列:Omnimate SL 包装:散装 零件状态:有效 类型:接头 针脚数:2 每级针脚数:2 级别数:1 间距:0.197"（5.00mm） 针座方向:垂直式 插线入口:- 端子类型:- 安装类型:- 电流 - IEC:- 电压 - IEC:- 电流 - UL:- 电压 - UL:- 线规或范围 - AWG:- 线规或范围 -?mm2:- 颜色:黑 工作温度:- 触头配接表面处理:- 特性:- 标准包装:1,000 |
| 1052000001 | 功能描述:SMIA55 CAMERA SOCKET BOTTOM CONT 制造商:molex, llc 系列:105200 包装:带卷（TR） 零件状态:有效 类型:相机插口 针脚或引脚数（栅格）:12（2 x 6） 间距 - 配接:0.028"（0.70mm） 触头表面处理 - 配接:金 触头表面处理厚度 - 配接:12μin（0.30μm） 触头材料 - 配接:铜合金 安装类型:表面贴装，通孔板式 特性:开放框架 端接:焊接 间距 - 柱:0.028"（0.70mm） 触头表面处理 - 柱:金 触头表面处理厚度 - 柱:闪存 触头材料 - 柱:铜合金 外壳材料:热塑塑胶 工作温度:-55°C ~ 85°C 端接柱长度:- 材料可燃性等级:UL94 V-0 额定电流:0.5A 接触电阻:- 标准包装:2,700 |
| 1052000008 | 制造商:Molex 功能描述:SMIA55 CAMERA SOCKET BOTTOM CONTACT 0.75 - Trays |
| 105200-0008 | 制造商:MOLEX 功能描述:SMIA55 CAMERA SOCKET BOTTOM C NTACT 0.75 制造商:Molex 功能描述: 制造商:Molex 功能描述:SMIA55 Camera Socket Bottom Contact 0.75 |
发布紧急采购，3分钟左右您将得到回复。