- 您现在的位置：买卖IC网 > Datasheet目录591 > 1213670-1 (TE Connectivity)TOOL SEATING ASSY FOR STACK RJ45 Datasheet资料下载
参数资料
| 型号： | 1213670-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | TOOL SEATING ASSY FOR STACK RJ45 |
| 标准包装： | 1 |
| 系列： | * |
408-8996
Maximum force occurs prior to the connector
assembly bottoming on the pc board.
tooling, connector assembly, or both. ?
properly seated on the connector assembly before
cycling the application tool.
For available application tools, call PRODUCT INFO
at the number at the bottom of page 1.
CAUTION Over-driving of the connector assembly will deform
parts critical to the quality of the connection.
!
4. SETUP
When setting up equipment to seat the connector
assembly, pay particular attention to the alignment of
the seating tool, connector assembly, and application
tool ram before cycling the application tool.
CAUTION If the seating tool and connector assembly are
improperly aligned, damage could occur to the
!
1. Set tool seating height to the dimension shown in
Figure 2 (application tool shut height will equal the
tool seating height PLUS the combined thicknesses
of the pc board and support fixture). After seating, a
gap of no more than 0.10 mm [.004 in.] between the
connector assembly standoffs and the pc board ?
is allowed.
5. SEATING (Figure 2)
1. Place the pc board on the support fixture.
2. Orient the seating tool over the connector
assembly so that the back plate is aligned with the
back of the connector assembly and the cutout is
aligned with the PoE chip set. Then lower the
seating tool until it bottoms on the connector
assembly.
3. Place the connector assembly on the pc board so
that the contacts and alignment posts are aligned
and started into the matching holes in the pc board.
4. Center the seating tool (with the connector
assembly) under the ram of the application tool.
Slowly lower the ram until it just meets the seating
tool. Verify alignment of pc board support, pc board,
connector assembly, and seating tool.
CAUTION Damage to the pc board, seating tool, or connector
assembly may occur if the seating tool is not
!
5. Cycle the application tool to seat the connector
assembly on the pc board. Then retract the ram,
NOTE
i
Use the tool seating height as a reference starting
point. This height may need to be adjusted to
obtain the amount allowed (maximum of 0.10 mm
[.004 in.]) between the standoffs of the connector
assembly and the pc board.
and carefully remove the seating tool by pulling it
straight from the connector assembly. ?
?
?
?
Seating Tool
Note: Not to Scale
Ram of Applicator Tool
(Fully Down)
Connector Assembly
Contacts and Alignment
Posts Inserted into Holes
in PC Board and PC
Board Support Fixture
Application Tool
Shut Height
(Ram Fully Down)
(See Section 4, Step 1)
A
B
DIMENSION A
Tool Seating Height
(With Connector Assembly Seated)
37.92 mm [1.493 in.]
DIMENSION B
Maximum Gap Allowed
0.10 mm [.004 in.]
PC Board
PC Board
Support Fixture
Figure 2
Rev A
2 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 1213783-1 | TOOL HAND CRIMP 16-26AWG |
| 1213860-1 | CERTI-CRIMP II ADAPT-SDE BENCH |
| 1214518-2 | TOOL EXTRACTION FOR AMPLIVAR |
| 1214695-1 | TOOL CRIMPER ASSY BACKSHELL |
| 121586-5236 | TOOL HAND CRIMP 20-26AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1213675-1 | 功能描述:手工工具 STRAIGHT ACTION ADAPT SUB-ASSY RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1213-680-0 | 制造商:Zierick Manufacturing Corporation 功能描述: |
| 1213680-1 | 制造商:TE Connectivity 功能描述:C-HEAD ADAPTER SUB-ASSY - Bulk |
| 1213681-1 | 制造商:TE Connectivity 功能描述:PIN,GROOVED - Bulk 制造商:TE CONNECTIVITY 功能描述:PIN,GROOVED |
| 1-213684-1 | 功能描述:D-Sub标准连接器 OBSOLETE RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤: |
发布紧急采购，3分钟左右您将得到回复。