- 您现在的位置：买卖IC网 > Datasheet目录591 > 1213670-1 (TE Connectivity)TOOL SEATING ASSY FOR STACK RJ45 Datasheet资料下载
参数资料
| 型号： | 1213670-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/3页 |
| 文件大小： | 0K |
| 描述： | TOOL SEATING ASSY FOR STACK RJ45 |
| 标准包装： | 1 |
| 系列： | * |
408-8996
NOTE
i
35.69 mm
[1.405 in.]
6. Check assembly for proper seating according to
the following:
a. the widest section of each compliant pin is
inside its intended pc board hole
b. each connector alignment post is in its
intended pc board hole
c. the connector assembly is seated on the pc
board with a seating height of 25.22 mm [.993 in.]
measured from the top of the connector assembly
(not including the panel ground springs) to the top
of the pc board
d. if present, the gap between the connector
assembly standoffs and the pc board is no more
than 0.10 mm [.004 in.]
For detailed application requirements of the
connector assembly, refer to Application
Specification 114-13147. ?
6. MAINTENANCE AND INSPECTION
The seating tool is assembled and inspected before
shipment. It is recommended that the seating tool be
inspected immediately upon arrival at your facility to
7. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 3. ?
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed should
be replaced by TE Connectivity to ensure quality and
reliability. Order replacement parts through your
representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 717-986-7605, or
write to:
CUSTOMER SERVICE (038-035) ?
TYCO ELECTRONICS CORPORATION ?
PO BOX 3608 ?
HARRISBURG PA 17105-3608
For customer repair service, call 1-800-526-5136.
98.35 mm
[3.872 in.]
ensure that it has not been damaged during shipment,
and that it conforms to the dimensions provided in
Figure 3.
6.1. Daily Maintenance
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and contaminants with a
clean, soft brush or a lint-free cloth. DO NOT use
1
2
4
29.72 mm
[1.17 in.]
35.69 mm
[1.405 in.]
3
objects that could damage the components.
2. When the seating tool is not in use, store it in a
REPLACEMENT PARTS
clean, dry area.
6.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the seating tool or be supplied to
personnel responsible for the seating tool assembly.
Inspection frequency should be based on amount of
use, working conditions, operator training and skill,
ITEM
1
2
3
4
PART
NUMBER
1213667-1
1213669-1
1213668-1
2-21002-1
DESCRIPTION
BLOCK, Top
PLATE, Back
PLATE, Side
SCREW, Button Head
Socket Cap, 8-32 X .375 in.
QTY PER
TOOL
1
1
2
and established standards.
Rev A
Figure 3
8. REVISION SUMMARY
Since the previous version of this document, the
following changes were made:
? Updated document to corporate requirements.
3 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 1213783-1 | TOOL HAND CRIMP 16-26AWG |
| 1213860-1 | CERTI-CRIMP II ADAPT-SDE BENCH |
| 1214518-2 | TOOL EXTRACTION FOR AMPLIVAR |
| 1214695-1 | TOOL CRIMPER ASSY BACKSHELL |
| 121586-5236 | TOOL HAND CRIMP 20-26AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1213675-1 | 功能描述:手工工具 STRAIGHT ACTION ADAPT SUB-ASSY RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1213-680-0 | 制造商:Zierick Manufacturing Corporation 功能描述: |
| 1213680-1 | 制造商:TE Connectivity 功能描述:C-HEAD ADAPTER SUB-ASSY - Bulk |
| 1213681-1 | 制造商:TE Connectivity 功能描述:PIN,GROOVED - Bulk 制造商:TE CONNECTIVITY 功能描述:PIN,GROOVED |
| 1-213684-1 | 功能描述:D-Sub标准连接器 OBSOLETE RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤: |
发布紧急采购，3分钟左右您将得到回复。