- 您现在的位置：买卖IC网 > Datasheet目录591 > 1213860-1 (TE Connectivity)CERTI-CRIMP II ADAPT-SDE BENCH Datasheet资料下载
参数资料
| 型号： | 1213860-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | CERTI-CRIMP II ADAPT-SDE BENCH |
| 标准包装： | 1 |
| 系列： | Certi-Crimp |
| 附件类型： | 手柄 |
| 适用于相关产品： | SDE 电动台式端接器 |
CERTI- CRIMP II Tool Holder Assembly 1213860- 1
408- 10021
Quick-- Release Pin
Quick-- Release Pin
Housing
Side
Housing Center
Housing Center
Housing
Side
3. INSTALLATION AND REMOVAL
Figure 2
B. Removal
Switch (Handle)
3.1. Installation and Removal of the CERTI- CRIMP II
Tool Holder Assembly 1213860- 1
DANGER
To avoid personal injury, be sure the SDE Electric
Bench Terminator is disconnected from the power
source prior to the installation or removal of the
tool holder assembly.
A. Installation
Before mounting the CERTI--CRIMP II Tool Holder
Assembly, always make sure the guide ram of the
terminator is in the lowest position. See Figure 3.
1. Be sure the terminator has been switched “off.”
2. Remove the locating pins from the tool holder
assembly.
3. Remove and/or replace the tool holder
assembly.
DANGER
To avoid personal injury, be sure the SDE Electric
Bench Terminator is disconnected from the power
source prior to the installation or removal of the
tool holder assembly.
4. When removing the tool holder assembly, make
sure that the guide ram of the terminator is in the
lowest position.
5. If installing or removing crimping dies, refer to
Paragraph 3.2.
1. Be sure that the terminator has been switched
off.
2. Be sure that the CERTI--CRIMP II tool holder
assembly is mounted with the switch (handle) in
the front, to facilitate die opening and closing.
3. Mount the tool holder assembly from the back
and lock with the guide (safety) pins. Refer to
Figure 3 and Figure 4.
4. Refer to Paragraph 3.2, to remove and install
the crimping dies.
3.2. Installation and Removal of CERTI- CRIMP II
Crimping Heads
DANGER To avoid personal injury, be sure the SDE Electric
Bench Terminator is disconnected from the power
source prior to the installation or removal of the
crimping heads.
As supplied, the tool holder assembly has three
quick--release pins installed (Figure 2 and Figure 4 ).
The two outer pins will be used to secure the two
outer housing tabs of the crimp head (exposed
portion of the crimp head) to the tool holder assembly.
2 of 5
Tyco Electronics Corporation
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 1214518-2 | TOOL EXTRACTION FOR AMPLIVAR |
| 1214695-1 | TOOL CRIMPER ASSY BACKSHELL |
| 121586-5236 | TOOL HAND CRIMP 20-26AWG |
| 122533-1 | TOOL HEAD FOR PISTOL GRIP |
| 122563-1 | TOOL SEATING FOR 2MM HM SHIELDS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1213862-1 | 功能描述:折皱器 ANVIL, WIRE RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1213869-1 | 制造商:TE Connectivity 功能描述:PLUG - Bulk |
| 1213871-1 | 制造商:TE Connectivity 功能描述:KIT,DUAL STROKE CYL. REBUILD - Bulk |
| 1213872-1 | 制造商:TE Connectivity 功能描述:BATTERY,14.4V NI MH,AUTOPRESS - Bulk |
| 1213873-1 | 功能描述:电池充电器 BATTERY CHARGER AUTOPRESS RoHS:否 制造商:Power-Sonic 化学性质:Sealed Lead Acid 输出电压:12 V 输出电流:500 mA 端接类型:Screw |
发布紧急采购，3分钟左右您将得到回复。