- 您现在的位置：买卖IC网 > Datasheet目录591 > 1213860-1 (TE Connectivity)CERTI-CRIMP II ADAPT-SDE BENCH Datasheet资料下载
参数资料
| 型号： | 1213860-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | CERTI-CRIMP II ADAPT-SDE BENCH |
| 标准包装： | 1 |
| 系列： | Certi-Crimp |
| 附件类型： | 手柄 |
| 适用于相关产品： | SDE 电动台式端接器 |
CERTI- CRIMP II Tool Holder Assembly 1213860- 1
There are four different crimp heights. Refer to
Figure 6.
408- 10021
4. When the tool holder assembly is not in use,
store it in a clean, dry area.
NOTE
i
Although Tyco Electronics normally recommends
Position No. 2 (adjustment of the manufacturer),
Positions No. 3 and No. 4 increase the travel of
the tool head, which decreases the crimp height.
Position No. 1 decreases the the travel of the
head, which increases the crimp height.
6.2. Lubrication
Lubricate all pins, pivot points, and bearing surfaces
with a high quality grease. It is recommended using
Molykote paste which is a commercially available
lubricant. Lubricate according to the following
schedule:
Use a Flat-- Bladed Screwdriver
Crimp Height Adjustment
(One Step Equals 0.1mm [.004 In.])
Figure 6
5. OPERATION
The tool holder assembly is used with the SDE
Electric Bench Terminator and a CERTI--CRIMP II
Crimping Head. For operating instructions, refer to
Customer Manual 409--10052.
6. PREVENTIVE MAINTENANCE AND INSPECTION
It is recommended that a maintenance and inspection
program be performed periodically to ensure
dependable and uniform terminations.
DANGER To avoid personal injury, ALWAYS DISCONNECT
the SDE Electric Bench Terminator before
performing maintenance or inspection.
6.1. Daily Maintenance
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or a lint--free cloth. DO
NOT use objects that could damage the adapter.
2. Make sure that all components are in place and
secure.
3. Make certain all surfaces are protected with a
thin coat of any good SAE 20 motor oil. DO NOT
oil excessively.
If the tool holder assembly is used daily—lubricate
daily
If the tool holder assembly is used
occasionally—lubricate weekly
If the tool holder assembly is used
weekly—lubricate monthly
6.3. Visual Inspection
Regular inspections should be performed by
quality--control personnel. A record of scheduled
inspections should remain with the tool holder
assembly or be supplied to personnel responsible for
the tool holder assembly. Though recommendations
call for at least one inspection a month, the frequency
should be based on amount of use, working
conditions, operator training and skill, and established
company policies.
1. Remove all lubrication and accumulated film by
immersing the tool holder assembly in a suitable
commercial degreaser that will not affect paint or
plastic.
2. Make certain all components are in place.
3. Check all bearing surfaces for wear. Replace
any worn parts. If replacements are necessary,
refer to Section 7, REPLACEMENT AND REPAIR.
7. REPLACEMENT AND REPAIR
Customer--replaceable parts are listed in Figure 7.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed
should be replaced by Tyco Electronics to ensure
quality and reliability. Order replacement parts
through your Tyco Electronics Representative, or call
1--800--526--5142, or send a facsimile of your
purchase order to 717--986--7605, or write to:
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105--3608
For customer repair service, call 1--800--526--5136.
8. REVISION SUMMARY
S Added “Original Instructions”
I
4 of 5
Tyco Electronics Corporation
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 1214518-2 | TOOL EXTRACTION FOR AMPLIVAR |
| 1214695-1 | TOOL CRIMPER ASSY BACKSHELL |
| 121586-5236 | TOOL HAND CRIMP 20-26AWG |
| 122533-1 | TOOL HEAD FOR PISTOL GRIP |
| 122563-1 | TOOL SEATING FOR 2MM HM SHIELDS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1213862-1 | 功能描述:折皱器 ANVIL, WIRE RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1213869-1 | 制造商:TE Connectivity 功能描述:PLUG - Bulk |
| 1213871-1 | 制造商:TE Connectivity 功能描述:KIT,DUAL STROKE CYL. REBUILD - Bulk |
| 1213872-1 | 制造商:TE Connectivity 功能描述:BATTERY,14.4V NI MH,AUTOPRESS - Bulk |
| 1213873-1 | 功能描述:电池充电器 BATTERY CHARGER AUTOPRESS RoHS:否 制造商:Power-Sonic 化学性质:Sealed Lead Acid 输出电压:12 V 输出电流:500 mA 端接类型:Screw |
发布紧急采购，3分钟左右您将得到回复。