- 您现在的位置：买卖IC网 > Datasheet目录591 > 1213860-1 (TE Connectivity)CERTI-CRIMP II ADAPT-SDE BENCH Datasheet资料下载
参数资料
| 型号： | 1213860-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | CERTI-CRIMP II ADAPT-SDE BENCH |
| 标准包装： | 1 |
| 系列： | Certi-Crimp |
| 附件类型： | 手柄 |
| 适用于相关产品： | SDE 电动台式端接器 |
CERTI- CRIMP II Tool Holder Assembly 1213860- 1
Switch
(Handle)
Guide
Ram
408- 10021
1. Remove the quick--release pins shown in
Figure 4.
2. Insert the exposed portion of the crimping head
into the tool holder assembly cavity.
3. Insert the two outer quick--release pins through
the holes in the tool holder assembly, and through
the holes in the two outer tabs of the crimping
head.
NOTE The outer quick--release pins will “snap” into
position when they are properly inserted.
i
4. Insert the center quick--release pin into the tool
holder assembly and through the holes in the ram
and the moveable die of the crimp head.
NOTE
i
The center quick--release pin will “snap” into
position when it is properly inserted.
Figure 3
The center pin will be used to secure the movable die
of the crimp head to the ram of the tool holder
assembly.
The finished assembly should appear as shown in
Figure 5.
B. Removal
To remove the crimping head, it will be necessary to
remove the three quick--release pins, and then
remove the crimp head from the tool holder assembly.
Quick--
Release
Pins
Tool
Holder
Assembly
(Typical)
Crimping
Head
Quick--
Release
Pin
Quick--
Release
Pins
Guide Pin Removed
Figure 4
A. Installation
These pins must be removed prior to installing the
crimping head.
SDE
Electric
Terminator
Figure 5
4. CRIMP HEIGHT ADJUSTMENT
Crimp height adjustment is required only if the crimp
height listed in the Tyco Electronics die specification
is not achieved.
Adjust the crimp height with a flat--bladed screwdriver.
Rev C
Tyco Electronics Corporation
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 1214518-2 | TOOL EXTRACTION FOR AMPLIVAR |
| 1214695-1 | TOOL CRIMPER ASSY BACKSHELL |
| 121586-5236 | TOOL HAND CRIMP 20-26AWG |
| 122533-1 | TOOL HEAD FOR PISTOL GRIP |
| 122563-1 | TOOL SEATING FOR 2MM HM SHIELDS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1213862-1 | 功能描述:折皱器 ANVIL, WIRE RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1213869-1 | 制造商:TE Connectivity 功能描述:PLUG - Bulk |
| 1213871-1 | 制造商:TE Connectivity 功能描述:KIT,DUAL STROKE CYL. REBUILD - Bulk |
| 1213872-1 | 制造商:TE Connectivity 功能描述:BATTERY,14.4V NI MH,AUTOPRESS - Bulk |
| 1213873-1 | 功能描述:电池充电器 BATTERY CHARGER AUTOPRESS RoHS:否 制造商:Power-Sonic 化学性质:Sealed Lead Acid 输出电压:12 V 输出电流:500 mA 端接类型:Screw |
发布紧急采购，3分钟左右您将得到回复。