- 您现在的位置：买卖IC网 > PDF目录18840 > 12217 (NVE Corp/Sensor Products)MAGNET 3.5MM DIA X 4MM THICK PDF资料下载
参数资料
| 型号： | 12217 |
| 厂商： | NVE Corp/Sensor Products |
| 文件页数： | 124/145页 |
| 文件大小： | 0K |
| 描述： | MAGNET 3.5MM DIA X 4MM THICK |
| 标准包装： | 10 |
| 系列： | * |
| 其它名称： | Q7078272A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页当前第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页
Application Notes
Offset Characteristics
When using the specified sensitivity to predict the output of a sensor, remember that the sensor
typically has a DC offset voltage. This is due to electrical bridge imbalance as well as external
magnetic field bias (earth’s field, magnets…). The output of the sensor without applying the current of
interest is the base line output. The effects of the current will be added to this base line value. For the
graphs shown on pages 130 and 131, the Y axis intercept is the base line offset. To determine the
output of the sensor for a given field, this Y intercept number must be added to the value obtained by
multiplying the current value by the slope.
AC
As mentioned previously, most information thus far has focused on DC applications. AC current
detection with an AA003-02 is unique and thus deserves special attention in a separate application.
Because the sensor is magnetically omni-polar, the output will be the same sign for either direction of
magnetic field. As an AC current changes direction, the field surrounding the conductor will also
change direction. The sensor’s output will produce a fully rectified output. Low current AC is
particularly laden with hysteretic errors. One method of creating both a bipolar output and a lower
error is to magnetically bias the sensor. Biasing is discussed above in this Engineering and Application
Notes booklet.
Part-to-Part Sensitivity
The data and evaluation thus far have focused on individual part performance. The part-to-part
performance will also be briefly examined here. Each current sensor is tested and sorted to be within
certain limits as given in the specification sections of this catalog. The main specification that affects
the output of the sensor is the sensitivity. The AA003-02 sensors are tested to a sensitivity range of 2.0
to 3.2 mV/V/Oe. The offset specification also affects the output. The offset is the zero current or
electrical imbalance of the Wheatstone bridge inside the sensor.
The magnetic field of the earth at NVE, is approximately 0.5G at a 70-degree angle to the horizon
(values will vary depending on geographical location). The effects of this magnetic field should be
analyzed in each application.
Care should be taken by the user to reduce the number and proximity of ferrous materials and magnetic
field producers around the sensor. This typically is not a concern, but in some highly populated boards,
this may be a necessity. Close proximity to such devices can increase the magnetic hysteresis or affect
the output. In turn, these devices will decrease the sensor’s output precision.
The output of the AA003-02 is functionally dependent on the distance between the sensor and the
current. The field from a current carrying conductor is inversely proportional to the distance from the
conductor. As the distance from the sensor to the conductor increases, the output from the sensor
decreases. Likewise, as the sensor moves closer to the conductor, the output will increase. For the data
analysis done in this report, the sensor was placed “live bug” over the current traces. In this
configuration, the actual sensor element is about 0.04" from the top of the PCB trace. The output will
increase with the current carrying conductor placed directly over-top of the sensor package. In this
configuration, the sensing element is approximately 0.02" from the surface of the conductor. This
distance change will account for an estimated doubling of sensor output.
- 124 -
www.nve.com phone: 952-829-9217 fax: 952-829-9189
相关PDF资料 |
PDF描述 |
|---|---|
| B512-2T-YDA | MOD DIODE SCR 25A 240VAC .250"QC |
| HAL 200-S | CURRENT TRANSDUCERS 200A 15V |
| B553-2 | MOD DIODE SCR 25A 280VAC ISO QC |
| B511F-2 | MOD DIODE SCR 25A 120VAC ISO QC |
| HAL 50-S | CURRENT TRANSDUCERS 50A 15V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 122170 | 制造商:Amphenol Connex 功能描述:TNC BLKHD CRMP JCK RG59-50--TF - Bag |
| 1-22170-6 | 制造商:TE Connectivity 功能描述:PIN,COTTER - Bulk 制造商:TE CONNECTIVITY 功能描述:PIN,COTTER |
| 1-22170-8 | 制造商:TE Connectivity 功能描述:PIN,COTTER - Bulk 制造商:TE CONNECTIVITY 功能描述:PIN,COTTER |
| 1-2217206-0 | 功能描述:BLADE, SLUG 制造商:te connectivity amp connectors 系列:* 零件状态:有效 标准包装:1 |
| 1-2217206-1 | 功能描述:BLADE, SLUG 制造商:te connectivity amp connectors 系列:* 零件状态:有效 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。