参数资料
| 型号： | 20-101-0435 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 33/100页 |
| 文件大小： | 0K |
| 描述： | MODULE RABBITCORE RCM2110 |
| 标准包装： | 1 |
| 系列： | RabbitCore® |
| 模块/板类型： | MPU 核心模块 |
| 适用于相关产品： | RCM2110 |
| 产品目录页面： | 620 (CN2011-ZH PDF) |
| 其它名称： | 316-1086 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
32
RabbitCore RCM2100
4.3 Serial Programming Cable
The programming cable is used to connect the RCM2100’s programming port to a PC
serial COM port. The programming cable converts the RS-232 voltage levels used by the
PC serial port to the TTL voltage levels used by the Rabbit 2000.
When the PROG connector on the programming cable is connected to the RCM2100’s
programming header, programs can be downloaded and debugged over the serial interface.
The DIAG connector of the programming cable may be used on the RCM2100’s program-
ming header with the RCM2100 operating in the Run Mode. This allows the programming
port to be used as a regular serial port.
4.3.1 Changing Between Program Mode and Run Mode
The RCM2100 is automatically in Program Mode when the PROG connector on the
programming cable is attached to the RCM2100, and is automatically in Run Mode when
no programming cable is attached. When the Rabbit 2000 is reset, the operating mode is
determined by the status of the SMODE pins. When the programming cable’s PROG
connector is attached, the SMODE pins are pulled high, placing the Rabbit 2000 in the
Program Mode. When the programming cable’s PROG connector is not attached, the
SMODE pins are pulled low, causing the Rabbit 2000 to operate in the Run Mode.
Figure 10. Switching Between Program Mode and Run Mode
A program “runs” in either mode, but can only be downloaded and debugged when the
RCM2100 module is in the Program Mode.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information on the pro-
gramming port and the programming cable.
RESET RabbitCore when changing mode:
Press RESET button (if using Prototyping Board), OR
Cycle power off/on
after removing or attaching programming cable.
To PC COM port
Run Mode
Program Mode
相关PDF资料 |
PDF描述 |
|---|---|
| 345-030-527-801 | CARDEDGE 30POS DUAL .100 GREEN |
| AT25640N-10SI-2.7 | IC EEPROM 64KBIT 3MHZ 8SOIC |
| 345-030-527-204 | CARDEDGE 30POS DUAL .100 GREEN |
| AT25640-10PI-2.7 | IC EEPROM 64KBIT 3MHZ 8DIP |
| 345-030-527-202 | CARDEDGE 30POS DUAL .100 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 20-101-0436 | 功能描述:模块化系统 - SOM RCM2120 RabbitCore Module RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0437 | 功能描述:子卡和OEM板 SR9205 16 in/8 out RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0439 | 功能描述:模块化系统 - SOM SR9215 SRC 8IN 16OUT RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0440 | 功能描述:模块配件 SR9510 Relay 8 RoHS:否 制造商:Lantronix 产品: 用于: |
| 20-101-0444 | 功能描述:子卡和OEM板 SR9320 A/D 4-20mA RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
发布紧急采购，3分钟左右您将得到回复。