参数资料
| 型号： | 20-101-0435 |
| 厂商： | Rabbit Semiconductor |
| 文件页数： | 83/100页 |
| 文件大小： | 0K |
| 描述： | MODULE RABBITCORE RCM2110 |
| 标准包装： | 1 |
| 系列： | RabbitCore® |
| 模块/板类型： | MPU 核心模块 |
| 适用于相关产品： | RCM2110 |
| 产品目录页面： | 620 (CN2011-ZH PDF) |
| 其它名称： | 316-1086 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页当前第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
User’s Manual
77
To maximize the availability of RCM2100 resources, the demonstration hardware (LEDs
and switches) on the Prototyping Board may be disconnected. This is done by cutting the
traces below the silk-screen outline of header JP1 on the bottom side of the Prototyping
Board. Figure B-4 shows the four places where cuts should be made. An exacto knife
would work nicely to cut the traces. Alternatively, a small standard screwdriver may be
carefully and forcefully used to wipe through the PCB traces.
Figure B-4. Where to Cut Traces to Permanently Disable
Demonstration Hardware on Prototyping Board
The power LED (PWR) and the RESET switch remain connected. Jumpers across the
appropriate pins on header JP1 can be used to reconnect specific demonstration hardware
later if needed.
Note that the pinout at location JP1 on the bottom side of the Prototyping Board (shown in
Figure B-4) is a mirror image of the top side pinout.
The Prototyping Board provides the user with RCM2100 connection points brought out con-
veniently to labeled points at headers J2 and J4 on the Prototyping Board. Small to medium
circuits can be prototyped using point-to-point wiring with 20 to 30 AWG wire between the
prototyping area and the holes at locations J2 and J4. The holes are spaced at 0.1" (2.5 mm),
Table B-2. Prototyping Board Jumper Settings
Header JP2
Pins
Description
1–2
PA0 to LED DS2
3–4
PA1 to LED DS3
5–6
PB2 to Switch S2
7–8
PB3 to Switch S3
S2
PB3
PB2
PA1
PA0
DS3
S3
DS2
Cut
JP1
Bottom Side
相关PDF资料 |
PDF描述 |
|---|---|
| 345-030-527-801 | CARDEDGE 30POS DUAL .100 GREEN |
| AT25640N-10SI-2.7 | IC EEPROM 64KBIT 3MHZ 8SOIC |
| 345-030-527-204 | CARDEDGE 30POS DUAL .100 GREEN |
| AT25640-10PI-2.7 | IC EEPROM 64KBIT 3MHZ 8DIP |
| 345-030-527-202 | CARDEDGE 30POS DUAL .100 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 20-101-0436 | 功能描述:模块化系统 - SOM RCM2120 RabbitCore Module RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0437 | 功能描述:子卡和OEM板 SR9205 16 in/8 out RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0439 | 功能描述:模块化系统 - SOM SR9215 SRC 8IN 16OUT RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0440 | 功能描述:模块配件 SR9510 Relay 8 RoHS:否 制造商:Lantronix 产品: 用于: |
| 20-101-0444 | 功能描述:子卡和OEM板 SR9320 A/D 4-20mA RoHS:否 制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
发布紧急采购，3分钟左右您将得到回复。