参数资料
型号: 20-101-0492
厂商: Rabbit Semiconductor
文件页数: 27/110页
文件大小: 0K
描述: MODULE OP6800 FULL-FEATURED
标准包装: 1
系列: SBC
模块/板类型: 单板计算机模块
适用于相关产品: OP6800
其它名称: 20-101-492
20-101-492-ND
User’s Manual
19
3.3 Serial Communication
The OP6800 has two RS-232 serial ports, which can be configured as one RS-232 serial
channel (with RTS/CTS) or as two RS-232 (3-wire) channels using the serMode software
function call. Table 3 summarizes the options.
The OP6800 also has one RS-485 serial channel and one CMOS serial channel. The
CMOS serial channel serves as the programming port.
All four serial ports operate in an asynchronous mode. An asynchronous port can handle 7
or 8 data bits. A 9th bit address scheme, where an additional bit is sent to mark the first byte
of a message, is also supported. Serial Port A, the CMOS programming port, can be oper-
ated alternately in the clocked serial mode. In this mode, a clock line synchronously clocks
the data in or out. Either of the two communicating devices can supply the clock. The
OP6800 boards typically use all four ports in the asynchronous serial mode. Serial Ports B
and C are used for RS-232 communication, and Serial Port D is used for RS-485 commu-
nication. The OP6800 uses an 11.0592 MHz crystal, which is doubled to 22.1184 MHz. At
this frequency, the OP6800 supports standard asynchronous baud rates up to a maximum
of 230,400 bps.
3.3.1 RS-232
The OP6800 RS-232 serial communication is supported by an RS-232 transceiver. This
transceiver provides the voltage output, slew rate, and input voltage immunity required to
meet the RS-232 serial communication protocol. Basically, the chip translates the Rabbit
2000’s CMOS/TTL signals to RS-232 signal levels. Note that the polarity is reversed by
an RS-232 circuit so that a +5 V input becomes approximately -10 V and 0 V is output as
+10 V. The RS-232 transceiver also provides the proper line loading for reliable commu-
nication.
RS-232 can be used effectively at the OP6800’s maximum baud rate for distances of up to
15 m.
3.3.2 RS-485
The OP6800 has one RS-485 serial channel, which is connected to the Rabbit 2000 Serial
Port D through an RS-485 transceiver. The half-duplex communication uses the Rabbit
2000’s PB6 pin to control the transmit enable on the communication line.
The OP6800 can be used in an RS-485 multidrop network. Connect the 485+ to 485+ and
485– to 485– using single twisted-pair wires (nonstranded, tinned) as shown in Figure 11.
Note that a common ground is recommended.
Table 3. Serial Communication Configurations
Mode
Serial Port
B
C
D
0
RS-232, 3-wire
RS-485
1
RS-232, 5-wire
CTS/RTS
RS-485
相关PDF资料
PDF描述
101-0492 INTERFACE OP6800 W/ETHERNET PORT
11FMN-BMTR-A-TB CONN FMN HSNG 11POS SGL REV SMD
11FMN-BMT-A-TF CONN FMN HSNG 11POS SNGL NOR SMD
AT24C01-10SI-2.7 IC EEPROM 1KBIT 400KHZ 8SOIC
AT24C01-10PI-2.7 IC EEPROM 1KBIT 400KHZ 8DIP
相关代理商/技术参数
参数描述
20-101-0494 功能描述:模块化系统 - SOM RCM2250 RabbitCore Module RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0495 功能描述:处理器配件 BASEPLATE RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
20-101-0497 功能描述:单板计算机 OP6810 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm
201-01050 功能描述:铝质电解电容器 - 带引线 1 uF Electrolytic Capacitor RoHS:否 制造商:Kemet 引线类型: 电容:220 uF 容差:20 % 电压额定值:25 V 工作温度范围: 端接类型:Radial 外壳直径:8 mm 外壳长度:11 mm 引线间隔:5 mm 产品:General Purpose Electrolytic Capacitors 封装:Bulk
201-0105-01 功能描述:印刷电路板和试验板 JTAG 20 Pin Connector RoHS:否 制造商:3M Electronic Solutions Division 产品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 长度:0.1 in 宽度: