参数资料
型号: 20-101-0492
厂商: Rabbit Semiconductor
文件页数: 51/110页
文件大小: 0K
描述: MODULE OP6800 FULL-FEATURED
标准包装: 1
系列: SBC
模块/板类型: 单板计算机模块
适用于相关产品: OP6800
其它名称: 20-101-492
20-101-492-ND
User’s Manual
41
5.2.3 Run the PINGME.C Demo
Connect a crossover cable from your computer’s Ethernet port to the OP6800’s RJ-45
Ethernet connector. Open this sample program from the SAMPLES\TCPIP\ICMP folder,
compile the program, and start it running under Dynamic C. When the program starts run-
ning, the green LNK light on the OP6800 should be on to indicate an Ethernet connection
is made. (Note: If the LNK light does not light, you may not have a crossover cable, or if
you are using a hub perhaps the power is off on the hub or you are not using a straight-
through Ethernet cable.)
The next step is to ping the board from your PC. This can be done by bringing up the MS-
DOS window and running the ping program:
ping 10.10.6.100
or by Start > Run
and typing the command
ping 10.10.6.100
Notice that the orange ACT light flashes on the OP6800 while the ping is taking place, and
indicates the transfer of data. The ping routine will ping the board four times and write a
summary message on the screen describing the operation.
5.2.4 Running More Demo Programs With a Direct Connection
The program SSI.C (SAMPLES\OP6800\TCPIP\) demonstrates how to make the
OP6800 a Web server. This program allows you to turn the LEDs on an attached Demon-
stration Board from the Tool Kit on and off from a remote Web browser. LED0 and LED1
on the OP6800 (LED1 and LED2 on the Demonstration Board) will match those on the
Web page. As long as you have not modified the TCPCONFIG 1 macro in the sample pro-
gram, enter the following server address in your Web browser to bring up the Web page
served by the sample program.
http://10.10.6.100.
Otherwise use the TCP/IP settings you entered in the LIB\TCPIP\TCP_CONFIG.LIB
library.
The sample program TELNET.C (SAMPLES\OP6800\TCPIP\) allows you to communi-
cate with the OP6800 using the Telnet protocol. This program takes anything that comes
in on a port and sends it out Serial Port B. It uses digital input IN00 (which is connected to
Demonstration Board switch SW1) to indicate that the TCP/IP connection should be
closed and high-current output OUT01 to indicate that there is an active connection.You
may change the digital input and output to suit your application needs.
Follow the instructions included in the sample program. Run the Telnet program on your
PC (Start > Run telnet 10.10.6.100). As long as you have not modified the TCP-
CONFIG 1
macro in the sample program, the IP address is 10.10.6.100 as shown; other-
wise use the TCP/IP settings you entered in the TCP_CONFIG.LIB library. Each character
you type will be printed in Dynamic C's STDIO window, indicating that the board is
receiving the characters typed via TCP/IP.
相关PDF资料
PDF描述
101-0492 INTERFACE OP6800 W/ETHERNET PORT
11FMN-BMTR-A-TB CONN FMN HSNG 11POS SGL REV SMD
11FMN-BMT-A-TF CONN FMN HSNG 11POS SNGL NOR SMD
AT24C01-10SI-2.7 IC EEPROM 1KBIT 400KHZ 8SOIC
AT24C01-10PI-2.7 IC EEPROM 1KBIT 400KHZ 8DIP
相关代理商/技术参数
参数描述
20-101-0494 功能描述:模块化系统 - SOM RCM2250 RabbitCore Module RoHS:否 制造商:Digi International 外观尺寸:ConnectCore 9P 处理器类型:ARM926EJ-S 频率:150 MHz 存储容量:8 MB, 16 MB 存储类型:NOR Flash, SDRAM 接口类型:I2C, SPI, UART 工作电源电压:3.3 V 最大工作温度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0495 功能描述:处理器配件 BASEPLATE RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
20-101-0497 功能描述:单板计算机 OP6810 RoHS:否 制造商:Ampro By ADLINK 外观尺寸:EPIC 处理器类型:Intel Atom D510 频率:1.66 GHz 存储容量:2 GB (max) 存储类型:DDR2, L2 Cache 接口类型:Ethernet, PS/2, SATA, Serial, USB 工作电源电压:5 V, 12 V 功耗:13 W 最大工作温度:+ 70 C 尺寸:165.1 mm x 114.3 mm
201-01050 功能描述:铝质电解电容器 - 带引线 1 uF Electrolytic Capacitor RoHS:否 制造商:Kemet 引线类型: 电容:220 uF 容差:20 % 电压额定值:25 V 工作温度范围: 端接类型:Radial 外壳直径:8 mm 外壳长度:11 mm 引线间隔:5 mm 产品:General Purpose Electrolytic Capacitors 封装:Bulk
201-0105-01 功能描述:印刷电路板和试验板 JTAG 20 Pin Connector RoHS:否 制造商:3M Electronic Solutions Division 产品:Jumper & Insulated Wires 描述/功能:Jumper wire, 22 AWG 0.1 inch 长度:0.1 in 宽度: