- 您现在的位置：买卖IC网 > PDF目录18714 > 4463-TCE30E915S-EK (Silicon Laboratories Inc)KIT EZRADIO TEST CARD SI4463 TX PDF资料下载
参数资料
| 型号： | 4463-TCE30E915S-EK |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 21/56页 |
| 文件大小： | 0K |
| 描述： | KIT EZRADIO TEST CARD SI4463 TX |
| 标准包装： | 1 |
| 系列： | EZRadioPRO® |
| 类型： | 收发器，ISM |
| 频率： | 915MHz |
| 适用于相关产品： | Si4463 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Si4464/63/61/60
Table 10. POR Timing
Variable
t PORH
t PORL
V RRH
V RRL
t SR
Description
High time for VDD to fully settle POR circuit
Low time for VDD to enable POR
Voltage for successful POR
Starting Voltage for successful POR
Slew rate of VDD for successful POR
Min
10
10
90%*Vdd
0
Typ
Max
150
1
Units
ms
ms
V
mV
ms
3.3.2. Shutdown State
The shutdown state is the lowest current consumption state of the device with nominally less than 30 nA of current
consumption. The shutdown state may be entered by driving the SDN pin (Pin 1) high. The SDN pin should be held
low in all states except the shutdown state. In the shutdown state, the contents of the registers are lost and there is
no SPI access. When coming out of the shutdown state a power on reset (POR) will be initiated along with the
internal calibrations. After the POR the POWER_UP command is required to initialize the radio. The SDN pin
needs to be held high for at least 10us before driving low again so that internal capacitors can discharge. Not
holding the SDN high for this period of time may cause the POR to be missed and the device to boot up incorrectly.
If POR timing and voltage requirements cannot be met, it is highly recommended that SDN be controlled using the
host processor rather than tying it to GND on the board.
3.3.3. Standby State
Standby state has the lowest current consumption with the exception of shutdown but has much faster response
time to RX or TX mode. In most cases standby should be used as the low power state. In this state the register
values are maintained with all other blocks disabled. The SPI is accessible during this mode but any SPI event,
including FIFO R/W, will enable an internal boot oscillator and automatically move the part to SPI active state. After
an SPI event the host will need to re-command the device back to standby through the “Change State” API
command to achieve the 50 nA current consumption. If an interrupt has occurred (i.e., the nIRQ pin = 0) the
interrupt registers must be read to achieve the minimum current consumption of this mode.
3.3.4. Sleep State
Sleep state is the same as standby state but the wake-up-timer and a 32 kHz clock source are enabled. The
source of the 32 kHz clock can either be an internal 32 kHz RC oscillator which is periodically calibrated or a
32 kHz oscillator using an external XTAL.The SPI is accessible during this mode but an SPI event will enable an
internal boot oscillator and automatically move the part to SPI active mode. After an SPI event the host will need to
re-command the device back to sleep. If an interrupt has occurred (i.e., the nIRQ pin = 0) the interrupt registers
must be read to achieve the minimum current consumption of this mode.
3.3.5. SPI Active State
In SPI active state the SPI and a boot up oscillator are enabled. After SPI transactions during either standby or
sleep the device will not automatically return to these states. A “Change State” API command will be required to
return to either the standby or sleep modes.
3.3.6. Ready State
Ready state is designed to give a fast transition time to TX or RX state with reasonable current consumption. In this
mode the Crystal oscillator remains enabled reducing the time required to switch to TX or RX mode by eliminating
the crystal start-up time.
3.3.7. TX State
The TX state may be entered from any of the state with the “Start TX” or “Change State” API commands. A built-in
sequencer takes care of all the actions required to transition between states from enabling the crystal oscillator to
ramping up the PA. The following sequence of events will occur automatically when going from standby to TX state.
1. Enable internal LDOs.
2. Start up crystal oscillator and wait until ready (controlled by an internal timer).
Rev 1.2
21
相关PDF资料 |
PDF描述 |
|---|---|
| 4463-TCE30E915R-EK | KIT EZRADIO TEST CARD SI4463 TX |
| 4463-TCE27F868-EK | KIT EZRADIO TEST CARD SI4463 TX |
| 4463-TCE20C915-EK | KIT EZRADIO TEST CARD SI4463 TX |
| DR-TXC100-315 | BOARD EVALUATION 315MHZ TXC100 |
| 4463-TCE20C868-EK | KIT EZRADIO TEST CARD SI4463 TX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4463-TSQ20D169-EK | 功能描述:射频开发工具 4463 20 dBm 169 MHz Test Card RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4463-TSQ27F169-EK | 功能描述:射频开发工具 4463 27 dBm 169 MHz Test Card RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4464 | 功能描述:以太网和电信连接器 SHIELD CONNECTOR RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
| 44640-01-445-1 | 制造商:UNBRANDED 功能描述:IC SOCKET +0.1UF 40WAY |
| 446405-1 | 功能描述:D-Sub混合触点连接器 SIZE 4 8C8 COAX-MIX 100 RoHS:否 制造商:FCI 触点布置: 位置/触点数量: 安装风格:Through Hole 安装角: 端接类型:Solder |
发布紧急采购，3分钟左右您将得到回复。