- 您现在的位置：买卖IC网 > PDF目录18714 > 4463-TCE30E915S-EK (Silicon Laboratories Inc)KIT EZRADIO TEST CARD SI4463 TX PDF资料下载
参数资料
| 型号： | 4463-TCE30E915S-EK |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 31/56页 |
| 文件大小： | 0K |
| 描述： | KIT EZRADIO TEST CARD SI4463 TX |
| 标准包装： | 1 |
| 系列： | EZRadioPRO® |
| 类型： | 收发器，ISM |
| 频率： | 915MHz |
| 适用于相关产品： | Si4463 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Si4464/63/61/60
5.2.3. Image Rejection and Calibration
Since the receiver utilizes a low-IF architecture, the selectivity will be affected by the image frequency. The IF
frequency is 468.75 kHz (Fxtal/64), and the image frequency will be at 937.5 kHz below the RF frequency. The
native image rejection of the Si446x family is 35 dB. Image rejection calibration is available in the Si446x to
improve the image rejection to more than 55 dB. The calibration is initiated with the IRCAL API command. The
calibration uses an internal signal source, so no external signal generator is required. The initial calibration takes
250 ms, and periodic re-calibration takes 100 ms. Re-calibration should be initiated when the temperature has
changed more than 30 °C.
5.2.4. Received Signal Strength Indicator
The received signal strength indicator (RSSI) is an estimate of the signal strength in the channel to which the
receiver is tuned. The RSSI measurement is done after the channel filter, so it is only a measurement of the
desired or undesired in-band signal power. There are two different methods for reading the RSSI value and several
different options for configuring the RSSI value that is returned. The fastest method for reading the RSSI is to
configure one of the four fast response registers (FRR) to return a latched RSSI value. The latched RSSI value is
measured once per packet and is latched at a configurable amount of time after RX mode is entered. The fast
response registers can be read in 16 SPI clock cycles with no requirement to wait for CTS. The RSSI value may
also be read out of the GET_MODEM_STATUS command. In this command, both the current RSSI and the latched
RSSI are available. The current RSSI value represents the signal strength at the instant in time the
GET_MODEM_STATUS command is processed and may be read multiple times per packet. Reading the RSSI in
the GET_MODEM_STATUS command takes longer than reading the RSSI out of the fast response register. After
the initial command, it will take 33 μ s for CTS to be set and then the four or five bytes of SPI clock cycles to read
out the respective current or latched RSSI values.
The RSSI configuration options are set in the MODEM_RSSI_CONTROL API property. The latched RSSI value
may be latched and stored based on the following events: preamble detection, sync detection, or a configurable
number of bit times measured after the start of RX mode (minimum of 4 bit times). The requirement for four bit
times is determined by the processing delay and settling through the modem and digital channel filter. In
MODEM_RSSI_CONTROL, the RSSI may be defined to update every bit period or to be averaged and updated
every four bit periods. If RSSI averaging over four bits is enabled, the latched RSSI value will be delayed to a
minimum of 7 bits after the start of RX mode to allow for the averaging. The latched RSSI values are cleared when
entering RX mode so they may be read after the packet is received or after dropping back to standby mode. If the
RSSI value has been cleared by the start of RX but not latched yet, a value of 0 will be returned if it is attempted to
be read.
The RSSI value read by the API could be translated to dBm by the following linear equation:
RSSI (in dBm) = (RSSI_value /2) – RSSIcal
RSSIcal in the above formula depends on the matching network, modem settings, and external LNA gain (if
present). The RSSIcal value can be obtained by a simple calibration with a signal generator connected at the
antenna input. Without external LNA, the value of RSSIcal is around 130 ±30.
During packet reception, it may be useful to detect whether a secondary interfering signal (desired or undesired)
arrives. To detect this event, a feature for RSSI jump detection is available. If the RSSI level changes by a
programmable amount during the reception of a packet, an interrupt or GPIO can be configured to notify the host.
The level of RSSI increase or decrease (jump) is programmable through the MODEM_RSSI_JUMP_THRESH API
property. If an RSSI jump is detected, the modem may be programmed to automatically reset so that it may lock
onto the new stronger signal. The chip may also be configured to automatically reset the receiver upon jump
detection in order to acquire the new signal. The configuration and options for RSSI jump detection are
programmed in the MODEM_RSSI_CONTROL2 API property. By default, RSSI jump detection is not enabled.
Rev 1.2
31
相关PDF资料 |
PDF描述 |
|---|---|
| 4463-TCE30E915R-EK | KIT EZRADIO TEST CARD SI4463 TX |
| 4463-TCE27F868-EK | KIT EZRADIO TEST CARD SI4463 TX |
| 4463-TCE20C915-EK | KIT EZRADIO TEST CARD SI4463 TX |
| DR-TXC100-315 | BOARD EVALUATION 315MHZ TXC100 |
| 4463-TCE20C868-EK | KIT EZRADIO TEST CARD SI4463 TX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4463-TSQ20D169-EK | 功能描述:射频开发工具 4463 20 dBm 169 MHz Test Card RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4463-TSQ27F169-EK | 功能描述:射频开发工具 4463 27 dBm 169 MHz Test Card RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4464 | 功能描述:以太网和电信连接器 SHIELD CONNECTOR RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: |
| 44640-01-445-1 | 制造商:UNBRANDED 功能描述:IC SOCKET +0.1UF 40WAY |
| 446405-1 | 功能描述:D-Sub混合触点连接器 SIZE 4 8C8 COAX-MIX 100 RoHS:否 制造商:FCI 触点布置: 位置/触点数量: 安装风格:Through Hole 安装角: 端接类型:Solder |
发布紧急采购，3分钟左右您将得到回复。