- 您现在的位置：买卖IC网 > PDF目录156623 > 4610M-901-103 KONDENSATOR NETZWERK PDF资料下载
参数资料
| 型号： | 4610M-901-103 |
| 英文描述： | KONDENSATOR NETZWERK |
| 中文描述： | KONDENSATOR NETZWERK |
| 文件页数： | 58/62页 |
| 文件大小： | 1883K |
| 代理商： | 4610M-901-103 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页当前第58页第59页第60页第61页第62页
Specifications are subject to change without notice.
337
These are the common
methods, materials and
maximum temperature/
time parameters for
soldering and cleaning
processes:
Soldering/Cleaning Methods
REFLOW
FLOW
Hot Air,
Infrared
Vapor Phase
Wave
Process Step
(Solvent)
(Aqueous)
Material
1.
Solder Paste Printing
X
RMA
2.
Adhesive Application
X
Epoxy
3.
Switch Placement
X
4.
Adhesive Cure
X
5. Flux Application
X
Rosin
5. Flux Application
X
Organic Acid
6. Solder (Reflow)
X
63/37 Sn/Pb
7. Solder (Flow)
X
63/37 Sn/Pb
8. Wash (Solvent)
X
ODS Free
9. Wash (Aqueous)
X
DI H2O; Detergent
High Pressure Fluids
X
Ultrasonics
X
Max. Temp.(°C)/Time (Seconds)
240/30
215/180
260/5
6
Solder
Reflow; Convection,
IR and Vapor Phase
GENERAL
Preheat sufficiently using both time
and temp. to bring the flux to activa-
tion and minimize thermal shock.
Consult your solder paste supplier for
the recommended profile.
RECOMMENDED
Typical IR/Convection profile.
Use convection or Vapor Phase when
possible and minimize the time above
reflow temperature.
CAUTION
Do not exceed time and temperature
reflow profile of 240°C for 30 sec. for
Hot Air/IR reflow and 215°C for 3
minutes for vapor phase reflow.
Minimize thermal shock by limiting
temperature ramps to 3°C/sec. and by
stabilizing board and component tem-
perature during preheating.
7
Solder
Flow (Wave)
GENERAL
For maximum component reliability
and performance, minimize the time
of temp. exposure above 200°C.
RECOMMENDED
Typical alloy is Sn63/Pb37. A typical
wave solder zone profile is 245C for
5 sec.
CAUTION
Always preheat before the soldier
wave using the temperature for flux
activation recommended by the man-
ufacturer.
Do not exceed 240C peak tempera-
ture for dual wave solder process
with a flow zone totaling 5 seconds.
Minimize thermal shock by limiting
temperature ramps to 3C/sec. and by
stabilizing board and component
temperature during preheating.
8
Wash
Solvent
GENERAL
Use solvent cleaning primarily
for nonpolar contaminants
such as rosin based flux
residues.
RECOMMENDED
Use any suitable washing sol-
vents that meet ODS require-
ments.
CAUTION
Limit excessive direct spray
pressure to 60 psi.
Allow the assembly to suffi-
ciently cool prior to the wash-
ing operation for minimized
thermal stress.
9
Wash
Aqueous
GENERAL
Use aqueous cleaning primarily
for polar contaminants such as
organic flux residues.
RECOMMENDED
Use De-ionized or Reverse
Osmosis water with multistage
rinsing. Post bake at 100C for
30 minutes to remove any resid-
ual moisture.
CAUTION
Limit excessive direct spray
pressure to 60 psi.
Allow the assembly to sufficient-
ly cool prior to the washing oper-
ation for minimized thermal
stress.
Board Rework Technique
GENERAL
Excessive and/or repeated high
temperature exposure may
affect the component perfor-
mance and reliability.
RECOMMENDED
Hot air reflow technique is pre-
ferred. Use No Clean or Rosin
based fluxes only, OA fluxes are
recommended.
CAUTION
Avoid the use of wave soldering
or soldering irons as a rework
technique. Avoid repeated and
excessive temperature exposure.
PRE-HEATING
(in air)
SOLDERING GRADUAL COOLING
(in air)
200°C
100°C
0°C
ONE MINUTE
MIN.
20 SECOND
MAX.
230°C
PRE-HEATING
(in air)
SOLDERING GRADUAL COOLING
(in air)
200°C
100°C
0°C
ONE MINUTE
MIN.
5 SECOND
MAX.
245°C
相关PDF资料 |
PDF描述 |
|---|---|
| 4610M-901-104 | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 4610M-902-103 | KONDENSATOR NETZWERK |
| 4610M-902-104 | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 4610X-101-101 | WIDERSTAND NETZWERK DICKFILM 100R 5ST |
| 4610X-101-102 | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4610M-901-103LF | 功能描述:电容器阵列与网络 10Pin 0.01uF 20% Bussed X7R RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| 4610M-901-104 | 功能描述:电容器阵列与网络 10Pin 0.1uF 20% Bussed X7R RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| 4610M-901-104LF | 功能描述:电容器阵列与网络 10Pin 0.1uF 20% Bussed X7R RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| 4610M-901-104LF | 制造商:Bourns Inc 功能描述:CAPACITOR ARRAY 0.1UF 50V X7R SIP 制造商:Bourns Inc 功能描述:CAPACITOR, ARRAY, 0.1UF, 50V, X7R, SIP |
| 4610M-901-104LF | 制造商:Bourns Inc 功能描述:CAPACITOR NETWORK 0.1UF ((NW)) |
发布紧急采购，3分钟左右您将得到回复。