- 您现在的位置：买卖IC网 > PDF目录18543 > 47820 (TE Connectivity)DIE TERMINYL 69051 8AWG PDF资料下载
参数资料
| 型号： | 47820 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/8页 |
| 文件大小： | 0K |
| 描述： | DIE TERMINYL 69051 8AWG |
| 标准包装： | 1 |
| 系列： | * |
Crimping Dies 47820 through
47825, 47915, and 47918
Instruction Sheet
408-- 1729
22 Mar 11 Rev J
Typical Crimping
Dies
Locator
Stationary
Die (Nest)
2. DESCRIPTION
Each crimping die consists of a stationary die (nest)
and a moving die (anvil). The stationary die features a
locator. Each die contains a color code dot that
matches the color code of the terminal and splice.
When mated, the dies form a crimping chamber.
3. DIE INSTALLATION AND REMOVAL
Moving
Die (Anvil)
DANGER
To avoid personal injury, ALWAYS release
hydraulic pressure to hose or control and
disconnect power unit from power supply before
installing or removing dies.
3.1. Installation
i
CRIMPING DIE
PART COLOR
NUMBER CODE DOT
47820 Red
47821 Blue
47822 Yellow
47823 Red
47824 Blue
47825 Yellow
47915 Red
47918 Blue
WIRE SIZE
(AWG)
8
6
4
2
1/0
2/0
3/0
4/0
HEAD OR TOOL
Hydraulic
Crimping Head
69051 or
Hydraulic Hand
Tool 59974--1
Hydraulic
Crimping Head
69066
1. Remove latch pin and open yoke on crimping
head. See Figure 2.
2. Loosen the setscrew in the yoke.
3. Insert the shank of the stationary die into the
yoke, and tighten the setscrew.
NOTE The stationary die has a large shank and the
moving die has a small shank, as shown in
Figure 2.
4. Extend the ram until the ram setscrew is visible.
Figure 1
1. INTRODUCTION
Crimping Dies 47820 through 47823 are used with
Crimping Head 69051 or Hand Tool 59974--1.
Crimping Dies 47824, 47825, 47915, and 47918 are
used with Crimping Head 69066. The dies crimp
pre--insulated AMPOWER* terminals onto wire sizes
4 through 1/0 AWG, TERMINYL* terminals and
splices onto wire sizes 8 through 4/0 AWG,
TERMINYL splices with step--down adapters onto
wire sizes 16--14 through 1/0 AWG, and
PLASTI--GRIP* terminals and splices onto wire sizes
8 through 4/0 AWG. Refer to Figure 1 to ensure
compatibility of crimping die, head or tool, and wire
size.
5. Loosen the setscrew in the ram.
6. Insert the shank of the moving die into the ram,
and tighten the setscrew.
Latch Pin Yoke Setscrew
(Removed)
Stationary Die
NOTE
i
Dimensions in this document are in millimeters
[with inches in brackets]. Figures and illustrations
are for reference only and are not drawn to scale.
Moving
Die
Shank
Shank
Color Code
Dot
For detailed information about the head or tool, refer
to the instructions packaged with the head or tool.
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
Crimping
Head
Figure 2
Ram
Setscrew
E 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1--800--722--1111
All Rights Reserved PRODUCT INFORMATION 1--800--522--6752
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
*Trademark. Other logos, product and/or Company names may be trademarks of their respective owners.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 8
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| AML22JBC2AD | SWITCH PUSHBUTTON DPDT 3A 125V |
| B82721A2401N21 | COIL CHOKE 27MH 0.4A HORZ |
| 252A103B60TA | POT JOYSTICK 10K OHM |
| B82721A2152N1 | COIL CHOKE 3.3MH 1.5A HORZ |
| 252B154B40TA | POT JOYSTICK 150K OHM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4782-01 | 制造商:FILTRAN 制造商全称:Filtran LTD 功能描述:Power Transformers L-Brackets |
| 4782-02 | 制造商:FILTRAN 制造商全称:Filtran LTD 功能描述:Power Transformers L-Brackets |
| 4782-03 | 制造商:FILTRAN 制造商全称:Filtran LTD 功能描述:Power Transformers L-Brackets |
| 478203000 | 制造商:C&K Components 功能描述: |
| 4782-04 | 制造商:FILTRAN 制造商全称:Filtran LTD 功能描述:Power Transformers L-Brackets |
发布紧急采购，3分钟左右您将得到回复。