- 您现在的位置：买卖IC网 > PDF目录18543 > 47820 (TE Connectivity)DIE TERMINYL 69051 8AWG PDF资料下载
参数资料
| 型号： | 47820 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/8页 |
| 文件大小： | 0K |
| 描述： | DIE TERMINYL 69051 8AWG |
| 标准包装： | 1 |
| 系列： | * |
408- 1729
CAUTION
!
To avoid damage to the dies, be sure that the
moving and stationary dies are properly oriented.
3. Insert stripped wire fully into terminal wire barrel.
The end of the conductor must not protrude more
than 1.60 mm [.063 in.] beyond the edge of the
wire barrel.
7. Activate the tool or power unit to allow the ram
to return to the “down” position.
8. Close the yoke, and insert the latch pin.
CAUTION
!
Do NOT turn or twist the wire or terminal during
insertion.
!
3.2. Removal
1. Remove latch pin and open yoke on crimping
head.
2. Loosen the setscrew in the yoke, and remove
the stationary die.
3. Extend the ram until the ram setscrew is visible.
4. Loosen setscrew in ram. Remove moving die.
4. CRIMPING PROCEDURE
4.1. Crimping Terminals
4. Remove crimping head latch pin and open yoke.
5. Place the terminal in the stationary die with the
edge of the wire barrel resting against the locator
and the bottom of the terminal tongue facing the
stationary die. See Figure 4.
6. Holding the terminal in place, close the yoke and
insert the latch pin.
CAUTION Be sure that the latch pin is fully inserted,
otherwise damage to the die and tool or head will
occur when the tool or power unit is activated.
DANGER
Avoid personal injury. When operating tool or
power unit, exercise caution while holding
terminals or wire near the crimping area.
7. Holding wire in place, activate tool or power unit
to complete crimp.
8. When crimp is completed, remove the latch pin,
open the yoke, and remove the terminal.
i
1. Strip wire to the dimensions listed in Figure 3.
Do not nick or cut the wire strands.
2. Select the proper color--coded terminal for the
wire size. The wire size stamped on the terminal
tongue and on the crimping die must match the
wire size selected.
NOTE If terminal sticks in die after crimping, apply a
rocking action to the terminal to remove it from
the die. Wipe light oil on the dies to prevent
sticking, or use spray dry lubricant.
9. Inspect the crimp according to Section 5.
Wire Strip Length
Typical Terminal
Wire Strip Length
Typical Splice
(Without Step- Down Adapter)
Wire Stop
Window Indent
WIRE
SIZE
(AWG)
TERMINYL TERMINAL AND SPLICE
TERMINAL SPLICE
WIRE STRIP LENGTH
PRE- - INSULATED
AMPOWER TERMINAL
PLASTI- - GRIP TERMINAL
AND SPLICE
8
6
4
7.96--9.53 [.313--.375]
11.18--12.70 [.440--.500]
11.18--12.70 [.440--.500]
15.48--17.07
20.24--19.45
19.45--21.03
[.609--.672]
[.797--.766]
[.766--.828]
----
----
10.72--12.29 [.422--.484]
11.51--12.29 [.453--.484]
15.47--16.26 [.609--.640]
15.47--16.26 [.609--.640]
2
1/0
2/0
3/0
4/0
11.43--13.08 [.450--.515]
18.54--20.24 [.730--.797]
18.54--20.24 [.730--.797]
19.05--20.64 [.750--.813]
19.45--21.03 [.766--.828]
21.83--30.18 [.859--1.188]
28.58--30.18 [1.125--1.188]
28.58--30.18 [1.125--1.188]
28.58--30.18 [1.125--1.188]
28.58--30.18 [1.125--1.188]
13.10--14.68 [.516--.578]
21.83--23.42 [.859--.922]
----
----
----
11.51--12.29 [.453--.484]
18.68--21.83 [.735--.859]
18.68--21.83 [.735--.859]
19.05--21.83 [.750--.859]
19.45--20.64 [.766--.813]
Figure 3
2 of 8
Rev J
相关PDF资料 |
PDF描述 |
|---|---|
| AML22JBC2AD | SWITCH PUSHBUTTON DPDT 3A 125V |
| B82721A2401N21 | COIL CHOKE 27MH 0.4A HORZ |
| 252A103B60TA | POT JOYSTICK 10K OHM |
| B82721A2152N1 | COIL CHOKE 3.3MH 1.5A HORZ |
| 252B154B40TA | POT JOYSTICK 150K OHM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4782-01 | 制造商:FILTRAN 制造商全称:Filtran LTD 功能描述:Power Transformers L-Brackets |
| 4782-02 | 制造商:FILTRAN 制造商全称:Filtran LTD 功能描述:Power Transformers L-Brackets |
| 4782-03 | 制造商:FILTRAN 制造商全称:Filtran LTD 功能描述:Power Transformers L-Brackets |
| 478203000 | 制造商:C&K Components 功能描述: |
| 4782-04 | 制造商:FILTRAN 制造商全称:Filtran LTD 功能描述:Power Transformers L-Brackets |
发布紧急采购，3分钟左右您将得到回复。