- 您现在的位置：买卖IC网 > Datasheet目录600 > 525690 (TE Connectivity)TOOL HAND CRIMP 18-20AWG Datasheet资料下载
参数资料
| 型号： | 525690 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP 18-20AWG |
| 标准包装： | 25 |
| 系列： | Certi-Crimp™, PIDG™, Plasti-Grip™ |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接头和端子，18-20 AWG |
| 特点： | 侧面插入，棘齿 |
PIDG terminals and splices feature a wire
“insulation grip.”
Window
Window
Indent
Double Action Hand Crimping Tools 525690 and 525691
8. Release the tool handles, and allow them to
open FULLY. Remove the crimped terminal or
splice.
9. For splices, position the remaining wire barrel in
the crimping chamber as shown in Figure 5, Detail
B. Repeat Steps 5 through 8.
10. Inspect crimped terminal or splice by checking
the features described in Figure 6. Terminals and
splices not meeting the described conditions
should NOT be used.
Crimping a Butt Splice
“B” Equals Wire Barrel
“C” Equals Insulation Barrel
PIDG Splice PLASTI--GRIP Splice
“C” “B” “C” “B”
Indent
411- 1097
4. INSULATION CRIMP ADJUSTMENT
The insulation barrel section of the crimping chamber
has three positions: 1 — tight, 2 — medium, and 3 —
loose. To adjust the grip resulting from the crimp of
the insulation barrel, proceed as follows:
4.1. PIDG Terminals and Splices
NOTE
i
1. Insert each insulation crimp adjustment pin into
Position 3. Refer to Figure 1.
CAUTION Make sure that both insulation crimp adjustment
pins are in the same position.
!
2. Position the terminal or splice in the crimping
chamber as described in Section 3.
Wire Stop
Wire Stop
3. Insert an UNSTRIPPED wire into ONLY the
insulation barrel of the terminal or splice.
4. Close the tool handles until the ratchet releases.
Detail A
Locator Seats in
Window Indent
5. Release the tool handles, and allow the handles
to open FULLY. Remove the crimped terminal or
splice.
6. Check the insulation barrel crimp by bending the
wire back and forth once. The terminal or splice
should retain its grip on the wire insulation. If it
does not, insert each insulation crimp adjustment
pin into the next position (Position 2).
i
End of Wire Conductor
Against Splice Wire Stop
Detail B
Locator Seats in
Window Indent
Wire Barrel
7. Repeat Steps 2 through 6 until the correct
insulation barrel grip is attained. DO NOT use a
tighter position than is necessary.
4.2. PLASTI- GRIP Terminals and Splices
NOTE PLASTI--GRIP terminals and splices feature a
wire “insulation support” only. Ideally, the terminal
or splice insulation should be in contact with the
wire insulation.
Insert each insulation crimp adjustment pin into
position according to the following:
End of Wire Conductor
Against Splice Wire Stop
CAUTION
!
Make sure that both insulation crimp adjustment
pins are in the same position.
Figure 5
Remaining
Wire Barrel
— Position 3 for wire having a large insulation
diameter.
— Position 2 for wire having a medium insulation
diameter.
— Position 1 for wire having a small insulation
diameter.
Rev D
Tyco Electronics Corporation
3 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| 525693 | TOOL HAND SOLIS STRATO 10-22AWG |
| 53200C | XFRMR CURR SENSE 10A 1:200 SMD |
| 532925-2 | TOOL HDI ALIGNMENT 540POS |
| 535072-1 | TOOL EURO TYPE C CONN INSERT |
| 539758-2 | DIE 2,8 TAB+EDS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 52569-0024 | 功能描述:HDMI, Displayport和DVI连接器 DVI CONNECTOR PLUG RoHS:否 制造商:Molex 系列:DisplayPort 产品类型:Displayport 型式:Female 位置/触点数量:20 端接类型:Solder 安装风格:SMD/SMT 方向:Right Angle 触点电镀:Gold |
| 525691 | 功能描述:手工工具 16-14 PIDG D.A.H.T. RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 52569-1029 | 制造商:FCI 功能描述: |
| 525692 | 功能描述:折皱器 HEAVY HEAD 12-10 RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 52569-2024 | 制造商:FCI 功能描述:DIGITAL VISUAL INTERFACE |
发布紧急采购，3分钟左右您将得到回复。