- 您现在的位置：买卖IC网 > Datasheet目录600 > 525690 (TE Connectivity)TOOL HAND CRIMP 18-20AWG Datasheet资料下载
参数资料
| 型号： | 525690 |
| 厂商： | TE Connectivity |
| 文件页数： | 6/7页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP 18-20AWG |
| 标准包装： | 25 |
| 系列： | Certi-Crimp™, PIDG™, Plasti-Grip™ |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接头和端子，18-20 AWG |
| 特点： | 侧面插入，棘齿 |
Double Action Hand Crimping Tools 525690 and 525691
411- 1097
Inspection of
Wire Barrel Section
of Crimping Chamber
Inspection of
Insulation Barrel Section
of Crimping Chamber
correct, and should be lubricated with a THIN coat of
any good SAE 20 motor oil. If not, return the tool for
evaluation and repair. See Section 6,
REPLACEMENT AND REPAIR.
Insulation Crimp Adjustment Pins in Position 1
Jaws Bottomed But
Not Under Pressure
5.3. Ratchet Inspection
Check the ratchet to ensure that the ratchet does not
release prematurely, allowing the jaws to open before
they have fully bottomed. Proceed as follows:
1. Remove traces of oil or dirt from the bottoming
surfaces of the jaws.
2. Obtain a 0.025 mm [.001 in.] shim that is
suitable for checking the clearance between the
bottoming surfaces of the jaws.
3. Select a terminal or splice and maximum size
wire for the terminal or splice.
GO Element Must Pass
Completely Through
Crimping Chamber
GO Element Must Pass
Completely Through Length of
Insulation Barrel Section But
Stop on Wire Barrel Section
4. Position the terminal or splice in the crimping
chamber according to Section 3, CRIMPING
PROCEDURE. Holding the wire in place, squeeze
the tool handles together until the ratchet releases.
Hold the tool handles in this position, maintaining
just enough pressure to keep the jaws closed.
5. Check the clearance between the bottoming
surfaces of the jaws. If the clearance is 0.025 mm
[.001 in.] or less, the ratchet is satisfactory. If
clearance exceeds 0.025 mm [.001 in.], the ratchet
is out of adjustment and must be repaired. See
Section 6, REPLACEMENT AND REPAIR.
6. REPLACEMENT AND REPAIR
NO-- GO Element May Start Entry, But Must Not
Pass Completely Through Crimping Chamber
Figure 8
4. Carefully insert the GO element into the
crimping chamber as shown in Figure 8; DO NOT
force it. For the wire barrel section of the crimping
chamber, the GO element must pass completely
through the crimping chamber. For the insulation
barrel section, the GO element must pass through
the length of the section but will stop against the
wire barrel section.
5. In the same manner, try to insert the NO--GO
element into the crimping chamber as shown in
Figure 8. The NO--GO element may begin entry,
but may not pass through the crimping chamber.
If the crimping chamber conforms to the gage
inspection, the tool is considered dimensionally
Customer--replaceable parts are listed in Figure 9.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed
should be replaced by Tyco Electronics to ensure
quality and reliability. Order replacement parts
through your representative, or call 1--800--526--5142,
or send a facsimile of your purchase order to
717--986--7605, or write to:
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105--3608
For customer repair service, call 1--800--526--5136.
7. REVISION SUMMARY
Revisions to this instruction sheet include:
S Updated document to corporate requirements
S Added new data to tables in Figure 7
6 of 7
Tyco Electronics Corporation
Rev D
相关PDF资料 |
PDF描述 |
|---|---|
| 525693 | TOOL HAND SOLIS STRATO 10-22AWG |
| 53200C | XFRMR CURR SENSE 10A 1:200 SMD |
| 532925-2 | TOOL HDI ALIGNMENT 540POS |
| 535072-1 | TOOL EURO TYPE C CONN INSERT |
| 539758-2 | DIE 2,8 TAB+EDS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 52569-0024 | 功能描述:HDMI, Displayport和DVI连接器 DVI CONNECTOR PLUG RoHS:否 制造商:Molex 系列:DisplayPort 产品类型:Displayport 型式:Female 位置/触点数量:20 端接类型:Solder 安装风格:SMD/SMT 方向:Right Angle 触点电镀:Gold |
| 525691 | 功能描述:手工工具 16-14 PIDG D.A.H.T. RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 52569-1029 | 制造商:FCI 功能描述: |
| 525692 | 功能描述:折皱器 HEAVY HEAD 12-10 RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 52569-2024 | 制造商:FCI 功能描述:DIGITAL VISUAL INTERFACE |
发布紧急采购，3分钟左右您将得到回复。