- 您现在的位置：买卖IC网 > Datasheet目录601 > 58443-1 (TE Connectivity)TOOL HEAD ASSEMBLY MTA .156 Datasheet资料下载
参数资料
| 型号： | 58443-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD ASSEMBLY MTA .156 |
| 标准包装： | 25 |
| 系列： | MTA-156 |
| 产品目录页面： | 200 (CN2011-ZH PDF) |
| 相关产品： | A2031-ND - TOOL MANUAL FOR SHELL CONNECTORS |
| 其它名称： | 58443-1-ND A30528 |
Feed- Through Head Assembly 58443- 1
2. After making the test crimp, depress the locating
pawl and push the receptacle out of the RIGHT
side of the head.
3. Inspect the termination according to Section 5.
If necessary, make the following adjustment:
— For the manual handle assembly or electric
power unit, if the wire is inserted too deep or not
deep enough in the contact slot, adjust the wire
insertion depth according to Paragraph 3.3. Then,
repeat the termination procedure and inspection.
— For the pistol grip pneumatic handle assembly
or pneumatic power bench assembly, if the wire is
inserted too deep in the contact slot, adjust the
wire insertion depth according to Paragraph 3.3.
If the wire is not inserted deep enough in the
contact slot, increase the air pressure by 69 kPa
[10 psi], and repeat the termination and inspection
procedure until either the proper insertion depth is
obtained or the air pressure is set to 483 kPa
[70 psi]. If the proper insertion depth is not reached
at 483 kPa [70 psi], return the air pressure to
276 kPa [40 psi], and adjust the wire insertion
depth according to Paragraph 3.3. Then, repeat
the termination procedure and inspection.
3.2. Insert Housing Adjustment
If the receptacle cannot be inserted into the head, or
if the receptacle is too loose in the head, loosen the
two screws on the insert housing, and adjust the
insert housing until the receptacle fits properly in the
head.
Discrete Wires
Wire Inserter
(Hidden)
Funnel
Area
Left Side of Head
408- 9607
3.3. Wire Insertion Depth Adjustment
1. Remove the head from the tool.
2. If the wire is inserted too deep, turn the rod
inserter adjuster clockwise one--sixth of a
revolution (the wire insertion depth will be
decreased by approximately 0.20 mm [.008 in.]).
If the wire is not inserted deep enough, turn the rod
inserter adjuster counterclockwise one--sixth of a
revolution (the wire insertion depth will be
increased by approximately 0.20 mm [.008 in.]).
Refer to Figure 4.
4. TERMINATION PROCEDURE
1. Determine the wire size and select the
appropriate receptacle (receptacles are
color--coded according to wire size).
2. Install the head onto the tool according to the
instructions packaged with the tool.
3. Refer to Figure 2, and:
— for the electric power unit, insert the receptacle
into the LEFT side of head (in the direction of the
arrow) until the first contact aligns with the wire
inserter.
— for the manual handle assembly, pistol grip
pneumatic handle assembly, and pneumatic power
bench assembly, depress and hold the trigger or
foot pedal (the wire inserter should extend), and
insert the receptacle into the LEFT side of head (in
Locating
Pawl
Index Ribs of
Receptacle
Wire Sub-- Assembly
Retainer
Retainer
Latch
Pistol Grip Manual
Handle Assembly
(Ref)
Feed Slide
Figure 2
Receptacle
2 of 5
Tyco Electronics Corporation
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 58448-2 | CRIMP TOOL D-SUB TERMINALS |
| 58483-1 | TOOL SMB DIE SET CONN MIL TYPE |
| 58500-1 | TOOL CRIMP SMB RG/174 W/DIE SET |
| 58509-1 | DIE SET 22-10AWG BUDGET |
| 58511-5 | FB 2MM ZPACK SEATING TOOL ASSY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58444-1 | 制造商:TE Connectivity 功能描述:DIE ASSY - Bulk |
| 58445-1 | 制造商:TE Connectivity 功能描述:HEAD ASSY - Bulk |
| 584469-000 | 制造商:TE Connectivity 功能描述:22759/33-24-98 - Cable Rools/Shrink Tubing |
| 584-48-1 | 制造商:Fox Electronics 功能描述:SMD,3.2X2.5,HCMOS OSC,3.3V,48.0000 MHZ - Cut Tape Product |
| 58448-2 | 功能描述:折皱器 HAND TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。