- 您现在的位置：买卖IC网 > Datasheet目录601 > 58443-1 (TE Connectivity)TOOL HEAD ASSEMBLY MTA .156 Datasheet资料下载
参数资料
| 型号： | 58443-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD ASSEMBLY MTA .156 |
| 标准包装： | 25 |
| 系列： | MTA-156 |
| 产品目录页面： | 200 (CN2011-ZH PDF) |
| 相关产品： | A2031-ND - TOOL MANUAL FOR SHELL CONNECTORS |
| 其它名称： | 58443-1-ND A30528 |
Feed- Through Head Assembly 58443- 1
the direction of the arrow) until it stops, then
release the trigger or foot pedal (the receptacle
should advance so that the first contact aligns with
the wire inserter).
4. Check that the locating pawl is resting between
the index ribs of the receptacle. See Figure 2. If
not, push the receptacle out of the RIGHT side of
the head, and re--insert it.
408- 9607
Inspection of Properly Terminated Wire
Contact Correct
Slot
Wire
Front of
Contact Beam Lead-- In
Transition
NOTE
i
After making the test crimp, the wire
sub--assembly retainer can be used (as shown in
Figure 2) to hold and locate the wires during
terminations. Pivot the retainer latch to open the
retainer.
5. Insert an unstripped wire into the funnel area
between the contact and the wire inserter until it is
in the desired location to be terminated.
6. Actuate the tool according to the instructions
included with the tool. When the cycle is
completed, the wire inserter will retract, and the
feed slide will automatically advance the receptacle
to the next contact position.
Strain Relief
Incorrect
NOTE
i
The locating pawl will move up and down as the
receptacle is automatically advanced through the
head. However, if movement is obstructed, or if
desired, depress the locating pawl and push the
receptacle out of the RIGHT side of the head.
Deformation
Figure 3
Cut in Wire
7. Repeat Steps 4 through 6 until all contacts have
been terminated.
8. Inspect each termination according to Section 5.
5. TERMINATION INSPECTION
Refer to Figure 3, and inspect each termination to
ensure the following:
— the wire is terminated past the lead--in transition
and is about halfway in the contact slot
— the wire is from 2.29 to 2.74 mm [.090 to
.108 in.] beyond the front of the contact beam
— the wire is NOT bottomed in the contact slot
— the contact beams are NOT deformed (if
damage is apparent, replace the contacts in
accordance with the instructions packaged with the
receptacle)
— the wire is NOT nicked or cut in any area other
than the contact slot
— the wires extend beyond the strain--reliefs of the
receptacle
NOTE Refer to 114--1020 for detailed application
requirements.
i
Wire Insertion Depth Adjustment
Turn Clockwise to Decrease
Wire Insertion Depth
Rod Inserter
Adjuster
Turn Counterclockwise to Increase
Wire Insertion Depth
Figure 4
6. MAINTENANCE AND INSPECTION
The following procedures have been established to
ensure the quality and reliability of the head. The
head should be checked daily, and a more detailed
inspection should be performed by your quality control
group on a regular basis.
6.1. Daily Maintenance
Each operator should be aware of, and responsible
for, the following steps of maintenance.
Rev C
Tyco Electronics Corporation
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 58448-2 | CRIMP TOOL D-SUB TERMINALS |
| 58483-1 | TOOL SMB DIE SET CONN MIL TYPE |
| 58500-1 | TOOL CRIMP SMB RG/174 W/DIE SET |
| 58509-1 | DIE SET 22-10AWG BUDGET |
| 58511-5 | FB 2MM ZPACK SEATING TOOL ASSY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58444-1 | 制造商:TE Connectivity 功能描述:DIE ASSY - Bulk |
| 58445-1 | 制造商:TE Connectivity 功能描述:HEAD ASSY - Bulk |
| 584469-000 | 制造商:TE Connectivity 功能描述:22759/33-24-98 - Cable Rools/Shrink Tubing |
| 584-48-1 | 制造商:Fox Electronics 功能描述:SMD,3.2X2.5,HCMOS OSC,3.3V,48.0000 MHZ - Cut Tape Product |
| 58448-2 | 功能描述:折皱器 HAND TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。