- 您现在的位置：买卖IC网 > Datasheet目录601 > 58448-2 (TE Connectivity)CRIMP TOOL D-SUB TERMINALS Datasheet资料下载
参数资料
| 型号： | 58448-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | CRIMP TOOL D-SUB TERMINALS |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, AMPLIMITE |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 圆形和 D-Sub 触点，20-28 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 431 (CN2011-ZH PDF) |
| 配用： | 6-66505-9-ND - CONN SOCKET 24-28AWG GOLD CRIMP 6-66506-1-ND - CONN PIN 20-24AWG GOLD CRIMP 7-66504-0-ND - CONN SOCKET 20-24AWG GOLD CRIMP 1-66504-2-ND - CONN SOCKET 20-24AWG GOLD CRIMP A104951-ND - CONN PIN 24-20AWG CRIMP GOLD A104952-ND - CONN PIN 28-24AWG CIMP 30GOLD A104950-ND - CONN SOCKET 24-20AWG 30GOLD A31986-ND - CONN SOCKET 24-28AWG GOLD CRIMP A31985-ND - CONN SOCKET 20-24AWG GOLD CRIMP A31911-ND - CONN PIN 20-24AWG GOLD CRIMP 更多... |
| 相关产品： | 1214310-1-ND - LOCATOR SUB-ASSEMBLY FOR 58448-2 |
| 其它名称： | A9990 |
408- 9357
Nut
Locator
Locator
Assembly
Tool Frame
Chamfered
Edge
Wire Crimper
Offset
Wire Anvil
Insulation
Crimper
Long Die Retaining Pins
(Supplied with Locator Assembly)
Short Die
Retaining Pins
Insulation
Anvil
Chamfered
Edge
Short Die Retaining
Screw
Long Die Retaining
Screw
Figure 2
i
3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY
AND LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles, and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
the chamfered sides and marked surfaces face
outward, when mounted in the moving jaw of the
tool frame.
3. Insert the two short die retaining pins through
the tool frame and into the anvils.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two long die retaining pins (supplied
with the locator assembly) through the tool frame
and into the crimpers.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
2 of 5
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Remove the pin from the center hole in the
locator assembly. Place the locator assembly over
the end of the long die retaining screw and long die
retaining pins. Position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
4. CRIMPING PROCEDURE
NOTE This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Section 5, CRIMP
HEIGHT INSPECTION, and Section 6,
RATCHET (Crimp Height) ADJUSTMENT, before
using the tool to crimp desired contacts.
Refer to Figure 1, and select wire of the specified size
and insulation diameter. Strip the wire to the length
indicated, taking care not to nick or cut wire strands.
Select an applicable contact and identify the
appropriate crimping chamber according to the wire
size markings on the tool.
Refer to Figure 3, and proceed as follows:
Rev E
相关PDF资料 |
PDF描述 |
|---|---|
| 58483-1 | TOOL SMB DIE SET CONN MIL TYPE |
| 58500-1 | TOOL CRIMP SMB RG/174 W/DIE SET |
| 58509-1 | DIE SET 22-10AWG BUDGET |
| 58511-5 | FB 2MM ZPACK SEATING TOOL ASSY |
| 58514-2 | DIE SET MR CONN USE WITH A9996 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58448-2 RENT | 制造商:TE Connectivity 功能描述:CRIMP TOOL HDP20RENT |
| 58448-3 | 功能描述:冲压机与冲模 PRO-CRIMPER DIE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 5-84-485 | 制造商:STANLEY 功能描述:PLIER SET 3PCE 制造商:Stanley Electric Co 功能描述:PLIER SET 3PCE |
| 584485-000 | 制造商:TE Connectivity 功能描述:HEAT SHRNK TBING POLYFN BLCK CUT PIECE - Bulk 制造商:TE Connectivity 功能描述:VERSAFIT-1/4-0-1.5IN-SM 制造商:TE Connectivity 功能描述:Heat Shrink Tubing ST Polyolefin Black Thin Loose Piece |
| 584487-000 | 制造商:TE Connectivity 功能描述:TXR40AB90-2412AI - Bulk 制造商:TE Connectivity 功能描述:ADPTR TINEL LOCK ANG SHELL 25, J 制造商:TE Connectivity 功能描述:Connector Accessories Tinel Lock Adapter Right Angle Aluminum Alloy Olive Drab Cadmium Over Electroless Nickel |
发布紧急采购，3分钟左右您将得到回复。