- 您现在的位置：买卖IC网 > Datasheet目录601 > 58545-1 (TE Connectivity)DIE SET UNINSULATED TERMINALS Datasheet资料下载
参数资料
| 型号： | 58545-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET UNINSULATED TERMINALS |
| 特色产品： | SOLISTRAND?, Budget, and DIAMOND GRIP? Terminals and Splices |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, Solistrand |
| 压接或电缆尺寸： | 10-22 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 端子及连接件 |
| 产品目录页面： | 384 (CN2011-ZH PDF) |
| 配用： | 328600-ND - CONN BUTT SPLICE UNINS 10-12AWG 1-34108-1-ND - CONN RING UNINS 16-22AWG #8 8-53555-1-ND - CONN SPADE 22-16AWG #2 SOLIS 8-35476-2-ND - CONN RING 12-10AWG #6 SOLIS 8-34126-1-ND - TERM RING 16-14AWG #3/8 SOLIS 8-34125-1-ND - TERM RING 16-14AWG #5/16 SOLIS 8-34114-1-ND - CONN RING 22-16AWG #5/16 SOLIS 8-34112-1-ND - CONN RING 16-22 AWG #10 SOLIS 8-34111-1-ND - CONN RING 22-16AWG #8 SOLIS 8-33459-2-ND - CONN RING 12-10AWG #5/16 SOLIS 更多... |
| 相关产品： | A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9813 |
Figure 2
5. Insert the die retaining screw through the
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full crimping.
The tool frame holds a die assembly with three
crimping chambers. The die assembly features an
upper die and a lower die. Die retaining screws are
used to position and secure the dies in the tool frame.
moving jaw and through the die. Tighten the screw
just enough to hold the die in place. Do not tighten
the screw completely at this time.
6. Carefully close the tool handles, making sure
that the anvils and indenters align properly.
Continue closing the tool handles until the ratchet
has engaged sufficiently to hold the dies in place,
then tighten both die retaining screws.
7. To disassemble, open the tool handles until the
ratchet releases, remove the two die retaining
screws, and slide the dies out of the tool jaws.
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the upper die in the stationary jaw of the
tool frame so that the largest indenter is facing
inward. See Figure 2.
3. Insert the die retaining screw through the
stationary jaw and through the die. Tighten the
screw just enough to hold the die in place. Do not
tighten the screw completely at this time.
4. Place the lower die in the moving jaw of the tool
frame so that the largest anvil is facing inward. See
Figure 2.
Refer to Figure 1 and select wire of the specified size
and insulation diameter. Strip the wire to the length
indicated, taking care not to nick or cut wire strands.
Select an applicable splice and identify the
appropriate crimping chamber according to the wire
size markings on the dies. Refer to Figure 3 and
proceed as follows:
相关PDF资料 |
PDF描述 |
|---|---|
| 58558-1 | CONSUMER BNC TOOL RG 58/59 |
| 58560-1 | TOOL CRIMP MODULAR 10 POS W/DIE |
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58545-2 | 功能描述:冲压机与冲模 SOLISTRAND 10-22 DIE ASSY RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58545-3 | 功能描述:冲压机与冲模 SDE DIE ASSY. 22-10 SOLISTRAND RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58545-4 | 功能描述:冲压机与冲模 SOLISTRAND 10-22 DIE ASSY. RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58546-1 | 功能描述:折皱器 TOOL W/DIE UNINS TRM RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58546-2 | 功能描述:折皱器 SOLIS 22-10AWG W/DIE AS (-1) RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。