- 您现在的位置：买卖IC网 > Datasheet目录601 > 58545-1 (TE Connectivity)DIE SET UNINSULATED TERMINALS Datasheet资料下载
参数资料
| 型号： | 58545-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET UNINSULATED TERMINALS |
| 特色产品： | SOLISTRAND?, Budget, and DIAMOND GRIP? Terminals and Splices |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, Solistrand |
| 压接或电缆尺寸： | 10-22 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 端子及连接件 |
| 产品目录页面： | 384 (CN2011-ZH PDF) |
| 配用： | 328600-ND - CONN BUTT SPLICE UNINS 10-12AWG 1-34108-1-ND - CONN RING UNINS 16-22AWG #8 8-53555-1-ND - CONN SPADE 22-16AWG #2 SOLIS 8-35476-2-ND - CONN RING 12-10AWG #6 SOLIS 8-34126-1-ND - TERM RING 16-14AWG #3/8 SOLIS 8-34125-1-ND - TERM RING 16-14AWG #5/16 SOLIS 8-34114-1-ND - CONN RING 22-16AWG #5/16 SOLIS 8-34112-1-ND - CONN RING 16-22 AWG #10 SOLIS 8-34111-1-ND - CONN RING 22-16AWG #8 SOLIS 8-33459-2-ND - CONN RING 12-10AWG #5/16 SOLIS 更多... |
| 相关产品： | A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9813 |
1. Hold tool so that the back (wire side) is facing
you. Squeeze tool handles together until the
ratchet releases, then allow them to open fully.
2. Center the splice wire barrel on the anvil of the
upper die as shown in Figure 3. If visible, be sure
to place the brazed seam on the splice toward the
indenter.
Figure 3
3. Hold the wire barrel in place and squeeze the
tool handles together until ratchet engages
sufficiently to hold the splice in position. Do NOT
deform the insulation barrel or wire barrel.
4. Insert stripped wire into the wire barrel, making
sure that the insulation does not enter the wire
barrel. See Figure 3.
5. Holding wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open, then remove crimped splice.
6. To crimp the other half of a splice, reposition the
uncrimped wire barrel in the crimping chamber, and
repeat the crimping procedure.
7. Inspect the crimped splice according to
Figure 4. Check the crimp height as described in
Section 5. If necessary, adjust the shut height as
described in Section 6.
Figure 4
This inspection requires the use of plug gages
conforming to the dimensions provided in Figure 5.
Tyco Electronics does not manufacture or market
these gages. To gage the crimping chamber, proceed
as follows:
1. Remove traces of oil or dirt from the crimping
chamber and plug gage.
2. Close the tool handles until the dies have
bottomed. Do NOT force dies beyond initial
contact.
3. Align the GO element with the crimping
chamber. Push element straight into the crimping
chamber without using force.
相关PDF资料 |
PDF描述 |
|---|---|
| 58558-1 | CONSUMER BNC TOOL RG 58/59 |
| 58560-1 | TOOL CRIMP MODULAR 10 POS W/DIE |
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58545-2 | 功能描述:冲压机与冲模 SOLISTRAND 10-22 DIE ASSY RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58545-3 | 功能描述:冲压机与冲模 SDE DIE ASSY. 22-10 SOLISTRAND RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58545-4 | 功能描述:冲压机与冲模 SOLISTRAND 10-22 DIE ASSY. RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58546-1 | 功能描述:折皱器 TOOL W/DIE UNINS TRM RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58546-2 | 功能描述:折皱器 SOLIS 22-10AWG W/DIE AS (-1) RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。