- 您现在的位置：买卖IC网 > Datasheet目录601 > 58644-1 (TE Connectivity)TOOL HEAD MTA .100 MASS INSERT Datasheet资料下载
参数资料
| 型号： | 58644-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD MTA .100 MASS INSERT |
| 标准包装： | 1 |
| 系列： | * |
408-4406
Terminated Test Connector
Contact Partially
Removed for
Inspection
Terminated Production Connector
Contact Slot
Lead-In ?
Transition
Wire Retainers Removed ?
(Both Sides)
No Cuts ?
in Wire
No Deformation of
Contact Beam
Figure 4
6. Then grip the wires on both sides of the
connector and carefully guide the connector out of
connector within five minutes of termination;
otherwise, an improper inspection may result. ?
Wire Inserted into Wire Slot
Ram
Handle Assembly
the ram.
7. Refer to Figure 4 and visually inspect the
connector according to the following. If wire
insertion depth is found to be improper, refer to
Section 5 for head adjustments.
CAUTION Wire insulation tends to return to form after being
compressed. It is important to inspect the
!
? Conductors are terminated past the lead-in
transition and halfway into the contact slot.
? Wires are not bottomed in contact slots.
? Wire insulation is not nicked or cut in any areas
except in the contact slots.
? Contact beams are not deformed. If damage is
evident, replace the damaged contact according to
NOTE
Surface of Head ?
Frame (Connector ?
Must Start Here)
Figure 5
the instructions packaged with the connector.
? Wire extends below the connector wire retainers. ?
For detailed inspection information, refer to
Application Specification 114-1019.
i
slots, pull them up and out of the slots before
continuing.
4. Actuate the handle assembly according to the
instructions packaged with the handle assembly.
CAUTION After the ram completes the stroke, no wires should
be left in the wire slots. If any wires are still in the
!
5. Depress the push rod to move the terminated
connector beyond the locating pawl in the ram.
Rev C
5. INSERTION DEPTH ADJUSTMENT
The terminating head is preset for nominal wire
insertion depth; however, it may be necessary to make
adjustments to the head, due to the wide range of
cable sizes used, as follows:
1. Remove the head from the handle assembly.
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 58646-1 | TOOL HEAD MTA .156 MASS INSERT |
| 58707-2 | TOOL DIE SET ONLY 16-20 AWG |
| 59239-8 | TOOL HAND 10-12AWG 14-16AWG HD |
| 59275 | TOOL CERTI-CRIMP PLASTI-G 20-26 |
| 59287-2 | TOOL HAND HEAVY PIDG 10-12AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58644-2 | 制造商:TE Connectivity 功能描述:MTA .100 MASS INSERTION PGH - Bulk |
| 5864-5001-09 | 功能描述:RF 连接器 PCB R/A Jack Rcept 50 OHM RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 5864-5001-10 | 功能描述:RF 连接器 MCX RA JCK PCB .155LG RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 5864-5002-10 | 功能描述:RF 连接器 OSX RA PCB JACK MICRO MIN SMT RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 5864-5003-10 | 功能描述:RF 连接器 MCX RA JCK PCB .115LG RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
发布紧急采购，3分钟左右您将得到回复。