- 您现在的位置：买卖IC网 > PDF目录19194 > 58707-1 (TE Connectivity)TOOL CRIMP W/DIE SET 16-20AWG PDF资料下载
参数资料
| 型号： | 58707-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP W/DIE SET 16-20AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，微型通用 MATE-N-LOK |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，16-20 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 233 (CN2011-ZH PDF) |
| 配用： | A34924-ND - CONN PIN 16-20AWG GOLD CRIMP A32447-ND - CONN SOCKET 16-20AWG GOLD CRIMP A28815-ND - CONN SOCKET 16-20AWG GOLD CRIMP A28814-ND - CONN SOCKET 16-20AWG TIN CRIMP A28807-ND - CONN PIN 16-20AWG GOLD CRIMP A28806-ND - CONN PIN 16-20AWG TIN CRIMP A25691-ND - CONN PIN 16-20AWG TIN CRIMP A25692-ND - CONN SOCKET 16-20AWG TIN CRIMP |
| 其它名称： | A30726 |
PRO- CRIMPER III Hand Crimping Tool Assembly 58707- 1
408- 4503
Chamfer
Wire Crimper
Offset
Nut
Insulation
Crimper
Locator
Assembly
Tool Frame
Die Retaining Pins
Wire Anvil
Insulation Anvil
Chamfer
Die Retaining Screws
Figure 2
2. DESCRIPTION (Figure 1 and Figure 2)
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with two
crimping sections.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Attached to the outside of the frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the upper die retaining screw to hold
the locator assembly in place.
3. INSTALLATION AND REMOVAL OF DIE SET
AND LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
2 of 5
Tyco Electronics Corporation
Rev A
相关PDF资料 |
PDF描述 |
|---|---|
| 210-7LPSTD | SWITCH SPST 7 SEC STRAIGHT TERM |
| 210-7MSTF | SWITCH RAISED ACTUATOR 7 SEC |
| 210-7LPSTF | SWITCH SPST 7 SEC LOW PROFILE |
| 210-7MST | SWITCH RAISED ACTUATOR 7 SEC |
| 210-7LPST | SWITCH SPST 7 SEC TAPE SEAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 587071N001 | 制造商:TE Connectivity 功能描述:102A951-3/42-8-CS5182 - Bulk |
| 58707-2 | 功能描述:冲压机与冲模 PROCRIMP MINI-U-MNL2 DIE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 5870R-0001A | 制造商:LG Corporation 功能描述:OPENER |
| 5870R-0002A | 制造商:LG Corporation 功能描述:OPENER |
| 5870R-0003A | 制造商:LG Corporation 功能描述:OPENER |
发布紧急采购，3分钟左右您将得到回复。