- 您现在的位置：买卖IC网 > PDF目录19194 > 58707-1 (TE Connectivity)TOOL CRIMP W/DIE SET 16-20AWG PDF资料下载
参数资料
| 型号： | 58707-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP W/DIE SET 16-20AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，微型通用 MATE-N-LOK |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，16-20 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 233 (CN2011-ZH PDF) |
| 配用： | A34924-ND - CONN PIN 16-20AWG GOLD CRIMP A32447-ND - CONN SOCKET 16-20AWG GOLD CRIMP A28815-ND - CONN SOCKET 16-20AWG GOLD CRIMP A28814-ND - CONN SOCKET 16-20AWG TIN CRIMP A28807-ND - CONN PIN 16-20AWG GOLD CRIMP A28806-ND - CONN PIN 16-20AWG TIN CRIMP A25691-ND - CONN PIN 16-20AWG TIN CRIMP A25692-ND - CONN SOCKET 16-20AWG TIN CRIMP |
| 其它名称： | A30726 |
i
PRO- CRIMPER III Hand Crimping Tool Assembly 58707- 1
4. CONTACT SUPPORT ADJUSTMENT (Figure 3)
NOTE The contact support is preset prior to shipment,
but minor adjustment may be necessary.
i
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
NOTE The ratchet has detents that create audible clicks
as the tool handles are closed.
i
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
408- 4503
contact is still being bent during crimping, repeat
the adjustment procedure.
5. CRIMPING PROCEDURE
NOTE This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be
verified as specified in Figure 4. Refer to Section
6, CRIMP HEIGHT INSPECTION, and Section 7,
RATCHET ADJUSTMENT, to verify crimp height
before using the tool to crimp desired contacts
and wire sizes.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact — insulation barrel first — through the front
of the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
must face the top of the tool. Place the contact up
into the nest so that the movable locator drops into
the slot in the contact. Refer to Figure 3. Butt the
front end of the wire barrel against the movable
locator.
Contact
Support
Locator
Back of Tool
(Wire Side)
Adjustment
Screw for
Contact
Support
Rev A
Wire
Figure 3
Tyco Electronics Corporation
Contact
(Typ)
Locator in Wire
Stop Slot
Strip Length
Wire Inserted
to Stop
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 210-7LPSTD | SWITCH SPST 7 SEC STRAIGHT TERM |
| 210-7MSTF | SWITCH RAISED ACTUATOR 7 SEC |
| 210-7LPSTF | SWITCH SPST 7 SEC LOW PROFILE |
| 210-7MST | SWITCH RAISED ACTUATOR 7 SEC |
| 210-7LPST | SWITCH SPST 7 SEC TAPE SEAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 587071N001 | 制造商:TE Connectivity 功能描述:102A951-3/42-8-CS5182 - Bulk |
| 58707-2 | 功能描述:冲压机与冲模 PROCRIMP MINI-U-MNL2 DIE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 5870R-0001A | 制造商:LG Corporation 功能描述:OPENER |
| 5870R-0002A | 制造商:LG Corporation 功能描述:OPENER |
| 5870R-0003A | 制造商:LG Corporation 功能描述:OPENER |
发布紧急采购，3分钟左右您将得到回复。