- 您现在的位置：买卖IC网 > PDF目录117394 > 5962-8768102VEA (TEXAS INSTRUMENTS INC) 2.2 A SWITCHING CONTROLLER, 1180 kHz SWITCHING FREQ-MAX, CDIP16 PDF资料下载
参数资料
| 型号： | 5962-8768102VEA |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2.2 A SWITCHING CONTROLLER, 1180 kHz SWITCHING FREQ-MAX, CDIP16 |
| 封装： | CERAMIC, DIP-16 |
| 文件页数： | 2/15页 |
| 文件大小： | 503K |
| 代理商： | 5962-8768102VEA |
HIGH CURRENT OUTPUTS
UDG-95114
GROUND PLANES
SLUS873A – JANUARY 2009 – REVISED APRIL 2009 ..................................................................................................................................................... www.ti.com
Each totem pole output of the UC1825A can deliver a 2-A peak current into a capacitive load. The output can
slew a 1000-pF capacitor by 15 V in approximately 20 ns. Separate collector supply (VC) and power ground
(PGND) pins help decouple the device's analog circuitry from the high-power gate drive noise. The use of 3-A
Schottky diodes (1N5120, USD245, or equivalent) as shown in the Figure 13 from each output to both VC and
PGND are recommended. The diodes clamp the output swing to the supply rails, necessary with any type of
inductive/capacitive load, typical of a MOSFET gate. Schottky diodes must be used because a low forward
voltage drop is required. DO NOT USE standard silicon diodes.
Figure 12. Power MOSFET Drive Circuit
Each output driver of these devices is capable of 2-A peak currents. Careful layout is essential for correct
operation of the chip. A ground plane must be employed. A unique section of the ground plane must be
designated for high di/dt currents associated with the output stages. This point is the power ground to which the
PGND pin is connected. Power ground can be separated from the rest of the ground plane and connected at a
single point, although this is not necessary if the high di/dt paths are well understood and accounted for. VCC
should be bypassed directly to power ground with a good high frequency capacitor. The sources of the power
MOSFET should connect to power ground as should the return connection for input power to the system and the
bulk input capacitor. The output should be clamped with a high current Schottky diode to both VCC and PGND.
Nothing else should be connected to power ground.
VREF should be bypassed directly to the signal portion of the ground plane with a good high frequency
capacitor. Low ESR/ESL ceramic 1-mF capacitors are recommended for both VCC and VREF. All analog
circuitry should likewise be bypassed to the signal ground plane.
10
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): UC1825A-SP
相关PDF资料 |
PDF描述 |
|---|---|
| 5962-0724303HXC | 1-OUTPUT 110 W DC-DC REG PWR SUPPLY MODULE |
| 555-0805-R27-G-00 | 1 ELEMENT, 0.27 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| 555-1008-1R5-J-36 | 1 ELEMENT, 1.5 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| 50A-821M-01 | 1 ELEMENT, 820 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
| 501-0430 | 1 ELEMENT, 150 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5962-8768102XA | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 5962-8768104V2A | 功能描述:电流型 PWM 控制器 High Spd PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| 5962-8768104VEA | 功能描述:电流型 PWM 控制器 High Spd PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| 5962-8768105VEA | 制造商:Texas Instruments 功能描述:Current Mode PWM Controller 100mA 16-Pin CDIP 制造商:Texas Instruments 功能描述:UC1825AJ-SP, HIGH SPEED PWM - Rail/Tube |
| 5962-87683012A | 制造商:Texas Instruments 功能描述:Decoder/Demultiplexer Dual 2-to-4 20-Pin LCCC Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。