- 您现在的位置：买卖IC网 > PDF目录68810 > 71M6511H-IGT (MAXIM INTEGRATED PRODUCTS INC) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64 PDF资料下载
参数资料
| 型号： | 71M6511H-IGT |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64 |
| 封装： | LQFP-64 |
| 文件页数： | 37/98页 |
| 文件大小： | 1278K |
| 代理商： | 71M6511H-IGT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页
71M6511/71M6511H
Single-Phase Energy Meter IC
DATA SHEET
NOVEMBER 2010
Page: 42 of 98
2005–2010 Teridian Semiconductor Corporation
V2.7
A Maxim Integrated Products Brand
Hardware Reset Mechanisms
Several conditions will cause a hardware reset of the 71M6511/6511H:
Voltage at the RESETZ pin low
Voltage at the E_RST pin low
Voltage at the V1 pin below reset threshold (VBIAS)
The crystal frequency monitor detected a crystal malfunction
Hardware Watchdog timer
Reset Pin (RESETZ)
When the RESETZ pin is pulled low (or when V1 < VBIAS), all digital activity in the chip stops while analog circuits are still
active. The oscillator and RTC module continue to run. Additionally, all I/O RAM bits are cleared.
Hardware Watchdog Timer
In addition to the basic software watchdog timer included in the 80515 MPU, an independent, robust, fixed-duration, hardware
watchdog timer (WDT) is included in the 71M6511/6511H. This timer will reset the MPU if it is not refreshed periodically, and
can be used to recover the MPU in situations where program control is lost.
The watchdog timer uses the RTC crystal oscillator as its time base and requires a reset under MPU program control at least
every 1.5 seconds. When the WDT overflow occurs, the MPU is momentarily reset as if RESETZ were pulled low for half of a
crystal oscillator cycle. Thus, after 4100 cycles of the CK32 (32768Hz clock), the MPU program will be launched from address
00.
An I/O RAM register status bit, WD_OVF (0x2002[2]), is set when WDT overflow occurs. This bit is powered by the VBAT
pin and can be read by the MPU to determine if the part is initializing after a WDT overflow event or after a power up. After
reading this bit, MPU firmware must clear WD_OVF. The WD_OVF bit is also cleared by the RESETZ pin.
The watchdog timer also includes an oscillator check. If the crystal oscillator stops or slows down, WD_OVF is set and a
system reset will be performed when the crystal oscillator resumes.
There is no internal digital state that deactivates the WDT. For debug purposes, however, the WDT can be disabled by tying
the V1 pin to V3P3 (see Figure 11 and WD Disable Threshold [V1-V3P3A] in the Comparator Section of the Electrical
Specifications). Of course, this also deactivates the power fault detection implemented with V1. Since there is no way in firm-
ware to disable the crystal oscillator or the WDT, it is guaranteed that whatever state the MPU might find itself in, it will be
reset to a known state upon watchdog timer overflow.
In normal operation, the WDT is reset by periodically writing a one to the WDT_RST bit. The watchdog timer is also reset when
WAKE=0 and, during development, when a 0x14 command is received from the ICE port.
Crystal Frequency Monitor
The hardware watchdog timer also includes an oscillator check. If the crystal oscillator stops or slows down, the I/O RAM
register WD_OVF is set and a system reset will be performed when the crystal oscillator resumes.
V1 Pin
The comparator at the V1 pin controls the state of the digital circuitry on the chip. When V1 < VBIAS (or when the RESTZ pin
is pulled low), all digital activity in the chip stops while analog circuits including the oscillator and RTC module are still active.
Additionally, when V1 < VBIAS, all I/O RAM bits are cleared. As long as V1 is greater than VBIAS, the internal 2.5V regulator
will continue to provide power to the digital section.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6511H-IGTR | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64 |
| 71M6521DE-IGTR/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
| 71M6521DE-IM/F | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 71M6521FE-IMR/F | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 71M6521DE-IGT/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6511H-IGT/F | 功能描述:计量片上系统 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6511H-IGTR | 制造商:Maxim Integrated Products 功能描述:RESID. HI PRECISION METR (1P, .1%) - Tape and Reel |
| 71M6511H-IGTR/F | 功能描述:计量片上系统 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6511-IGT | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Single-Phase Energy Meter IC |
| 71M6511-IGT/F | 功能描述:计量片上系统 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。