- 您现在的位置：买卖IC网 > PDF目录68810 > 71M6511H-IGT (MAXIM INTEGRATED PRODUCTS INC) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64 PDF资料下载
参数资料
| 型号： | 71M6511H-IGT |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64 |
| 封装： | LQFP-64 |
| 文件页数： | 69/98页 |
| 文件大小： | 1278K |
| 代理商： | 71M6511H-IGT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页当前第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页
71M6511/71M6511H
Single-Phase Energy Meter IC
DATA SHEET
NOVEMBER 2010
Page: 71 of 98
2005–2010 Teridian Semiconductor Corporation
V2.7
A Maxim Integrated Products Brand
GAIN_ADJ is a scaling factor for power measurements based on temperature (when in internal temperature compensation
mode). In general, for higher temperatures it is lower than 16384 and higher than 16384 for lower temperatures. GAIN_ADJ is
mainly dependent on the PPMC, PPMC2 and TEMP_X register values. This parameter is automatically computed by the CE
and is used by the CE for temperature compensation.
CE
Address
Name
Description
0x40
TEMP_X
Deviation from Calibration temperature. LSB = 0.1
0C.
0x54
TEMP_RAW_X
Filtered, unscaled reading from temperature sensor. This
value should be written to TEMP_NOM during meter
calibration.
0x2E
GAIN_ADJ
Scales all voltage and current inputs. 16384 provides
unity gain. Default is 16384. If EXT_TMP = 0, GAIN_ADJ
is updated by the CE.
Pulse Generation
Input variables: The combination of the PULSE_SLOW and PULSE_FAST parameters control the speed of the pulse rate. The
default values of 1 and 1 will maintain the original pulse rate given by the Kh equation.
WRATE controls the number of pulses that are generated per measured Wh and VARh quantities. The lower WRATE it is the
slower is the pulse rate for measured power quantity. The metering constant Kh is derived from WRATE as the amount of
energy measured for each pulse. That is, if Kh = 1Wh/pulse, a power applied to the meter of 120V and 30A results in one
pulse per second. If the load is 240V at 150A, ten pulses per second will be generated.
Control is transferred to the MPU for pulse generation if EXT_PULSE > 0. In this case, the pulse rate is determined by
APULSEW and APULSER. The MPU has to load the source for pulse generation in APULSEW and APULSER to generate pulses.
Irrespective of the EXT_PULSE, status the output pulse rate controlled by APULSEW and APULSER is implemented by the CE
only. By setting EXT_PULSE > 0, the MPU is providing the source for pulse generation. If EXT_PULSE is negative, W0SUM_X
and VAR0SUM_X are the default pulse generation sources. In this case, creep cannot be controlled since it is an MPU function.
The maximum pulse rate is FS /2= 1260.3Hz (MUX_DIV = 1).
PULSE_WIDTH allows adjustment of the pulse width for compatibility with calibration and other external equipment. When
MUX_DIV = 1, the minimum pulse width possible is 397s.
The maximum time jitter is 397s (for MUX_DIV = 1) and is independent of the number of pulses measured. Thus, if the pulse
generator is monitored for 1 second, the peak jitter is 397PPM. After 10 seconds, the peak jitter is 39.7PPM. The average jitter
is always zero. If it is attempted to drive either pulse generator faster than its maximum rate, it will simply output at its
maximum rate without exhibiting any roll-over characteristics. The actual pulse rate, using WSUM as an example, is:
Hz
F
WSUM
WRATE
X
RATE
S
46
2
=
Where FS = 2520.6Hz (sampling frequency for MUX_DIV = 1) or 3276.8Hz (sampling frequency for MUX_DIV = 2) and X is the
pulse gain factor derived from CE variables PULSE_SLOW and PULSE_FAST (see table below).
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6511H-IGTR | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP64 |
| 71M6521DE-IGTR/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
| 71M6521DE-IM/F | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 71M6521FE-IMR/F | SPECIALTY ANALOG CIRCUIT, QCC68 |
| 71M6521DE-IGT/F | SPECIALTY ANALOG CIRCUIT, QFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6511H-IGT/F | 功能描述:计量片上系统 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6511H-IGTR | 制造商:Maxim Integrated Products 功能描述:RESID. HI PRECISION METR (1P, .1%) - Tape and Reel |
| 71M6511H-IGTR/F | 功能描述:计量片上系统 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6511-IGT | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Single-Phase Energy Meter IC |
| 71M6511-IGT/F | 功能描述:计量片上系统 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。