参数资料
型号: 71M6513H-DB
厂商: Maxim Integrated Products
文件页数: 69/112页
文件大小: 0K
描述: BOARD DEMO 71M6513H ENERGY METER
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
主要目的: 电源管理,电度表/功率表
嵌入式:
已用 IC / 零件: 71M6513H
已供物品: 2 个板,线缆,CD,电源
71M6513/71M6513H Demo Board User’s Manual
3.2
D6513T3C1 BOARD DESCRIPTION: JUMPERS, SWITCHES AND
TEST POINTS
The items described in the following tables refer to the flags in Figure 3-2.
Item #
1
Reference
Designator
JP1
Name
PS_SEL[0]
Use
Two-pin header. When the jumper is installed the on- board
power supply (AC signal) is used to power the demo board.
When not installed, the board must be powered by an external
supply connected to J1. Normally installed.
2,8,9
TP2, TP4, TP6
VA, VB, and VC
Two pin header test points. One pin is the VA, VB or VC line
voltage input to the IC and the other pin is ground.
3,5,6,7
J9, J4, J6, J8
Neutral, VA_IN,
VB_IN, VC_IN
VA_IN, VB_IN, and VC_IN are the line voltage inputs. Each
point has a resistor divider that leads to the respective pin on
the chip that is the voltage input to the ADC. These inputs are
spade terminals on the bottom of the board.
Caution: High Voltage! Do not touch these pins!
4
J1
5 Volt external
Plug for connecting the external 5 VDC power supply.
supply
10
SW2
RESET
Chip reset switch: When the switch is pressed, the RESETZ
pin is pulled low, which resets the IC into a known state.
11
J12
Test Point for the
Optical Interface
Five-pin header allowing access to the OPT_RX and OPT_TX
signals. Pins 1 and 2 can be used to connect a LED. Pins 3, 4,
and 5 can be used to connect a photo-transistor.
12
D5
WATTS
Red LED. This LED functions as a pulse output for test and
calibration (Wh).
13
JP6
GND, DIO3, V3P3
Three-pin header. This header can be used for general
purpose DIO.
14
15
TP15, TP16
TP20
GND
SEG26/DIO06
GND test point
Two-pin header. This header can be used to pick up the signal
for the VARS LED output.
16
TP21
SEG27/DIO07
Two-pin header. This header can be used to pick up the signal
for the WATTS LED output.
17
D6
VARS
Red LED. This LED functions as a pulse output for test and
calibration (VARh).
18,23
J11,J10
--
Two 2x12 headers for the LCD connection. The LCD daughter
board plugs into the male (J10) and female (J11) headers.
19
20
JP12
JP13,JP14,
JP15
DIO Test Point
DIO00, DIO01,
DIO02
9-pin header for monitoring DIO15 to DIO21.
Three two-pin headers for monitoring the DIO00, DIO01, and
DIO02 signals.
Table 3-4: D6513T3C1 Demo Board Description
Page: 69 of 112
? 2005-2006 TERIDIAN Semiconductor Corporation
Revision 5.6
相关PDF资料
PDF描述
71M6515H-DB BOARD DEMO 71M6515H ENERGY METER
71M6521FE-DB BOARD DEMO FOR 71M6521FE
71M6531F-DB BOARD DEMO 71M6531F
71M6533-DB BOARD DEMO 71M6533
71M6534H-DB BOARD DEMO 71M6534H
相关代理商/技术参数
参数描述
71M6513H-IEL 制造商:未知厂家 制造商全称:未知厂家 功能描述:71M6513
71M6513H-IEL/F 功能描述:计量片上系统 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6513H-IELR 功能描述:计量片上系统 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6513H-IELR/F 功能描述:计量片上系统 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6513H-IGT/F 功能描述:计量片上系统 - SoC 3-Phase Energy Meter I/C RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel