参数资料
型号: 71M6531D-IMR/F
厂商: Maxim Integrated
文件页数: 52/121页
文件大小: 0K
描述: IC ENERGY METER 128KB 68-QFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
系列: *
Data Sheet 71M6531D/F-71M6532D/F
1.5.16 Hardware Watchdog Timer
FDS 6531/6532 005
V3P3
V3P3 - 10mV
V3P3 -
400mV
VBIAS
V1
WDT dis-
abled
Normal
operation,
WDT
enabled
Battery
modes
An independent, robust, fixed-duration, watchdog timer (WDT) is included
in the 71M6531D/F and 71M6532D/F. It uses the RTC crystal oscillator as
its time base and must be refreshed by the MPU firmware at least every
1.5 seconds. When not refreshed on time, the WDT overflows and the part
is reset as if the RESET pin were pulled high, except that the I/O RAM bits
will be in the same state as after a wake-up from SLEEP or LCD modes
(see the I/O RAM description in Section 4.2 for a list of I/O RAM bit states
after RESET and wake-up). 4100 oscillator cycles (or 125 ms) after the
WDT overflow, the MPU will be launched from program address 0x0000.
A status bit, WD_OVF, is set when the WDT overflow occurs. This bit is
preserved in LCD mode (not in SLEEP mode) and can be read by the MPU
when WAKE rises to determine if the part is initializing after a WDT over-
flow event or after a power-up. After it is read, the MPU firmware must
clear WD_OVF . The WD_OVF bit is also cleared by the RESET pin.
There is no internal digital state that deactivates the WDT.
0V
Figure 17: Functions defined by V1
The WDT can be disabled by tying the V1 pin to V3P3 (see Figure 17 ). Of course, this also deactivates
V1 power fault detection. Since there is no method in firmware to disable the crystal oscillator or the
WDT, it is guaranteed that whatever state the part might find itself in, upon watchdog overflow, the part
will be reset to a known state.
Asserting ICE_E will also deactivate the WDT. This is the only method that will work in BROWNOUT
mode. In normal operation, the WDT is reset by periodically writing a one to the WDT_RST bit. The
watchdog timer is also reset when the internal signal WAKE = 0 (see Section 2.5 Wake-Up Behavior ).
If enabled with the IEN_WD_NROVF bit in I/O RAM, an interrupt occurs roughly 1 ms before the WDT resets
the chip. This can be used to determine the cause of a WDT reset since it allows the code to log its state
(e.g. the current PC value, loop counters, flags, etc.) before a WDT reset occurs.
52
Rev 2
相关PDF资料
PDF描述
V48C28H75BG2 CONVERTER MOD DC/DC 28V 75W
ECA10DTKD CONN EDGECARD 20POS DIP .125 SLD
T95S334K035LZAL CAP TANT 0.33UF 35V 10% 1507
V48C28H75BG CONVERTER MOD DC/DC 28V 75W
SS8P4C-M3/87A DIODE SCHOTTKY 8A 40V SMPC
相关代理商/技术参数
参数描述
71M6531F 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6531F-DB 功能描述:开发板和工具包 - 8051 71M6531F Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
71M6531F-IM/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6531F-IM/F3 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6531F-IM/F4 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel