参数资料
型号: 71M6533G-IGTR/F
厂商: Maxim Integrated
文件页数: 10/132页
文件大小: 0K
描述: IC ENERGY METER 3PH 100LQFP
标准包装: 400
系列: Single Converter Technology®
输入阻抗: 40 千欧 ~ 90 千欧
测量误差: 0.1%
电压 - 高输入/输出: 2V
电压 - 低输入/输出: 0.8V
电流 - 电源: 10mA
电源电压: 3 V ~ 3.6 V
测量仪表类型: 三相,中性相位
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 64-LQFP
供应商设备封装: 64-LQFP(10x10)
包装: 带卷 (TR)
71M6533/G/H and 71M6534/H Data Sheet
FDS_6533_6534_004
1.2.2
Input Multiplexer
The input multiplexer applies the input signals from the pins IAP/IAN, VA, IBP/IBN, VB, ICP/ICN, VC, and
IDP/IDN to the input of the ADC. Additionally, using the alternate multiplexer selection, it has the ability to
select temperature and the battery voltage. One input is applied per time slot.
The multiplexer can implement from one to 10 time slots (states) per frame as controlled by the I/O RAM
field MUX_DIV[3:0] . The multiplexer always starts at state 1 and proceeds until as many states as defined
by MUX_DIV[3:0] have been converted.
The multiplexer can be operated in two modes:
?
?
During a normal multiplexer cycle ( MUX_ALT = 0), the signals selected in the I/O RAM SLOTn_SEL[3:0]
fields are processed. These are typically the signals from the IA, IB, IC, ID and VA, VB, and VC pins.
During the alternate multiplexer cycle ( MUX_ALT = 1), the signals selected in the SLOTn_SEL[3:0] fields
are processed. These signals typically comprise the temperature signal (TEMP), the battery monitor
(VBAT) and some of the voltage signals such as VA, VB, and VC. To prevent unnecessary drainage on
the battery, the battery monitor is enabled only with the BME bit ( IO RAM 0x2020[6]) .
The alternate multiplexer cycles are usually performed infrequently (every second or so) by the MPU. In
order to prevent disruption of the voltage tracking mechanism and voltage allpass networks of the CE,
VA, VB, and VC are not replaced in the alternate cycles.
The current inputs can be configured to be used in differential mode, using the pin pairs IAP/IAN,
IBP/IBN, ICP/ICN, and IDP/IDN. The fourth current input is available to support measurement of a fourth
or neutral phase.
In a typical application, IAP/IAN, IBP/IBN, ICP/ICN, and IDP/IDN are connected to current transformers
that sense the current on each phase of the line voltage. VA, VB, and VC are typically connected to the
phase voltages via resistor dividers.
Multiplexer advance, FIR initiation and VREF chopping are controlled by the internal MUX_CTRL signal.
Additionally, MUX_CTRL launches each pass through the CE program. Conceptually, MUX_CTRL is
clocked by CK32, the 32768Hz clock from the PLL block. The behavior of MUX_CTRL is governed by
MUX_ALT , EQU[2:0] , CHOP_E[1:0] , and MUX_DIV[3:0] .
The MUX_ALT bit requests an alternative multiplexer frame. The bit may be asserted on any MPU cycle
and may be subsequently deasserted on any cycle including the next one. A rising edge on MUX_ALT will
cause MUX_CTRL to wait until the next multiplexer frame and implement a single alternate multiplexer frame.
The inputs converted during normal and alternate frames are selectable using the pointers to signals.
SLOTn_SEL[3:0] selects the input signal for the nth state in a standard multiplexer frame, while
SLOTn_ALTSEL[3:0] selects the input for the nth state in an alternate multiplexer frame. For example, if
SLOT0_SEL[3:0] contains 0 and SLOT1_SEL[3:0] contains 1, signal selection 0, equivalent to IA (see Table 1 ),
will be applied for the first time slot, while signal 1, equivalent to VA, will be applied for the second time
slot. See Table 1 for a typical assignment of values for the SLOTn_SEL[3:0] and SLOTn_ALTSEL[3:0]
registers assuming seven time slots ( MUX_DIV[3:0] = 7) for the processing of three voltage and current
phases plus an additional neutral current.
The correlation between signal numbers, CE memory addresses, and analog signals is given in Table 3 .
For the processing of three voltage and current phases in a typical polyphase meter without neutral
measurement, MUX_DIV[3:0] is set to 6, and SLOT6_SEL[3:0] as well as SLOT6_ALTSEL[3:0] would be
empty.
10
Rev 2
相关PDF资料
PDF描述
71M6543F-IGT/F IC ENERGY METERING
71M6545-IGT/F IC ENERGY METERING
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
相关代理商/技术参数
参数描述
71M6533H 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6533H-IEL 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IEL/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IELR 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC
71M6533H-IELR/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Precision Energy Meter IC