- 您现在的位置：买卖IC网 > Datasheet目录299 > 71M6543F-IGT/F (Maxim Integrated Products)IC ENERGY METERING Datasheet资料下载
参数资料
| 型号： | 71M6543F-IGT/F |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 68/154页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING |
| 标准包装： | 90 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页当前第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页
71M6543F/71M6543G Data Sheet
1) An external host reads data from CE locations to obtain metering information. This can be used in
applications where the 71M6543 function as a smart front-end with preprocessing capability. Since the
addresses are in 16-bit format, any type of XRAM data can be accessed: CE, MPU, I/O RAM, but not
SFRs or the 80515-internal register bank.
2) A communication link can be established via the SPI interface: By writing into MPU memory locations,
the external host can initiate and control processes in the 71M6543 MPU. Writing to a CE or MPU
location normally generates an interrupt, a function that can be used to signal to the MPU that the
byte that had just been written by the external host must be read and processed. Data can also be
inserted by the external host without generating an interrupt.
3) An external DSP can access front-end data generated by the ADC. This mode of operation uses the
71M6543 as an analog front-end (AFE).
4) Flash programming by the external host (SPI Flash Mode).
SPI Transactions
A typical SPI transaction is as follows. While SPI_CSZ is high, the port is held in an initialized/reset state.
During this state, SPI_DO is held in high impedance state and all transitions on SPI_CLK and SPI_DI are
ignored. When SPI_CSZ falls, the port begins the transaction on the first rising edge of SPI_CLK. As
shown in Table 56 , a transaction consists of an optional 16 bit address, an 8 bit command, an 8 bit status
byte, followed by one or more bytes of data. The transaction ends when SPI_CSZ is raised. Some
transactions may consist of a command only.
When SPI_CSZ rises, SPI command bytes that are not of the form x0000000 cause the SPI_CMD (SFR
0xFD) register to be updated and then cause an interrupt to be issued to the MPU. The exception is if the
transaction was a single byte. In this case, the SPI_CMD byte is always updated and the interrupt issued.
SPI_CMD is not cleared when SPI_CSZ is high.
The SPI port supports data transfers up to 10 Mb/s. A serial read or write operation requires at least 8
clocks per byte, guaranteeing SPI access to the RAM is no faster than 1.25 MHz, thus ensuring that SPI
access to DRAM is always possible.
Table 56: SPI Transaction Fields
Field
Name
Address
Command
Status
Data
Required
Yes, except
single byte
transaction
Yes
Yes, if transaction
includes DATA
Yes, if transaction
includes DATA
Size
(bytes)
2
1
1
1 or
more
Description
16-bit address. The address field is not required if the transaction
is a simple SPI command.
8-bit command. This byte can be used as a command to the
MPU. In multi-byte transactions, the MSB is the R/W bit. Unless
the transaction is multi-byte and SPI_CMD is exactly 0x80 or
0x00, the SPI_CMD register is updated and an SPI interrupt is
issued. Otherwise, the SPI_CMD register is unchanged and the
interrupt is not issued.
8-bit status field, indicating the status of the previous transaction.
This byte is also available in the MPU memory map as
SPI_STAT (I/O RAM 0x2708) . See Table 58 for the contents.
The read or write data. Address is auto incremented for each
new byte.
The SPI_STAT byte is output on every SPI transaction and indicates the parity of the previous transaction
and the error status of the previous transaction. Potential error sources are:
?
?
68
71M6543 not ready
Transaction not ending on a byte boundary.
v2
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6545-IGT/F | IC ENERGY METERING |
| 720-10007-00300 | CBL D-SUB 9PIN FMAL-25PIN FML 3M |
| 720-10010-00025 | CBL DSUB 9PIN FML-25PIN MAL .25M |
| 720-10020-00300 | CBL DSUB 9PIN FML-9PIN MALE 3M |
| 720-10021-00300 | CBL DSUB 9PIN FML-9PIN FEMAL 3M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6543F-IGTR/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC |
发布紧急采购，3分钟左右您将得到回复。