- 您现在的位置：买卖IC网 > PDF目录11583 > 73S8010R-IM/F (Maxim Integrated Products)IC SMART CARD INTERFACE 32-QFN PDF资料下载
参数资料
| 型号： | 73S8010R-IM/F |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/25页 |
| 文件大小： | 0K |
| 描述： | IC SMART CARD INTERFACE 32-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 490 |
| 控制器类型： | 智能卡接口 |
| 接口： | I²C |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电流 - 电源： | 1.5mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 管件 |
73S8010R Data Sheet
DS_8010R_022
18
Rev. 1.6
3.4
Card Power Supply
The card power supply is provided by the LDO regulator, and controlled by the digital ISO-7816-3
sequencer. Card voltage selection is carried out by bit 2 of the control register.
Choice of the VCC capacitor:
Depending on the application, the requirements in terms of both the VCC minimum voltage and the
transient currents that the interface must be able to provide to the card are different. An external
capacitor must be connected between the VCC pin and the card ground in order to guarantee stability of
the LDO regulator, and to handle the transient requirements. The type and value of this capacitor can be
optimized to meet the desired specification. Table 14 shows the recommended capacitors for each VPC
power supply configuration and applicable specification.
Table 14: Choice of VCC Pin Capacitor
3.5
Over-temperature Monitor
A built-in detector monitors die temperature. When an over-temperature condition occurs (resulting from
a heavily loaded card interface, including short circuits, for example), a card deactivation sequence is
initiated, and a fault condition is reported to the system controller (bit 4 of the status register is set and an
interrupt is generated).
3.6
On-chip Oscillator and Card Clock
The Teridian 73S8010R device has an on-chip oscillator that can generate the smart card clock using an
external crystal connected between the XTALIN and XTALOUT pins to set the oscillator frequency.
When the card clock signal is available from another source, it can be connected to the pin XTALIN, and
in this case, the XTALOUT pin should be left unconnected.
The card clock frequency may be chosen from 4 different division rates, defined by the Clksel2 and
Clksel1 bits (bits 5 and 6) of the I
2C Control register, as listed in Table 15.
Table 15: Card Clock Divisor Options
Specification Requirements
System Requirements
Specification
Min VCC Voltage
allowed during
transient current
Max Transient
Current Charge
Min VPC Power
Supply required
Capacitor
Type
Capacitor
Value
EMV 4.0
4.6 V
30 nA
s
4.75 V
X5R/X7R
with
ESR<100 m
Ω
3.3
ΩF
ISO-7816-3
4.5 V
20 nA
s
4.75 V
1
ΩF
Clksel2
Clksel1
Card Clock
0
Clkin / 8
0
1
Clkin / 4
1
0
Clkin / 2
1
Clkin (Xtalin)
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16LC54C-04I/P | IC MCU OTP 512X12 18DIP |
| 73S8024RN-IL/F | IC SMART CARD INTERFACE 28-SOIC |
| PIC12LCE519-04/SN | IC MCU OTP 1KX12 LV W/EE 8SOIC |
| PIC16F882T-I/SO | IC PIC MCU FLASH 2KX14 28SOIC |
| PIC24F08KL200T-I/ST | IC MCU 16BIT 8KB FLASH 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8010R-IMR/F | 功能描述:I2C 接口集成电路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010R-IMR/F1 | 功能描述:I2C 接口集成电路 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010R-IMR/F2 | 功能描述:I2C 接口集成电路 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8014BL-IL/F | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| 73S8014BN | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Smart Card Interface |
发布紧急采购，3分钟左右您将得到回复。