- 您现在的位置：买卖IC网 > PDF目录11583 > 73S8010R-IM/F (Maxim Integrated Products)IC SMART CARD INTERFACE 32-QFN PDF资料下载
参数资料
| 型号： | 73S8010R-IM/F |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/25页 |
| 文件大小： | 0K |
| 描述： | IC SMART CARD INTERFACE 32-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 490 |
| 控制器类型： | 智能卡接口 |
| 接口： | I²C |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电流 - 电源： | 1.5mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 管件 |
DS_8010R_022
73S8010R Data Sheet
Rev. 1.6
15
I
2C-bus Write to Control Register
The I
2C-bus Write command to the control register follows the format shown in Figure 5. After the START
condition, the master sends a slave address. This address is seven bits long followed by an eighth bit
which is an opcode bit (R/W) – a ‘zero’ indicates the master will write data to the control register. After
the R/W bit, the ’zero’ ACK bit is sent to the master by the device. The master now starts sending the 8
bits of data to the control register during the DATA bits. After the DATA bits, the ‘zero’ ACK bit is sent to
the master by the device. The master should send the STOP condition after receiving this ACK bit.
1-7
8
9
1-8
9
ADDRESS bits
R/
W bit
ACK bit
DATA bits
ACK bit
STOP
condition
START
condition
SCL
SDA
MSB
LSB
Figure 5: I
2C Bus Write Protocol
Table 12 describes the Status Register bits.
Table 12: Status Register Description
Power On Reset = 0x04
Name
Bit
Description
PRES
0
Set when the card is present (pin PRES is high); reset when the card is not present.
PRESL
1
Set when the PRES pin changes state (rising/falling edge); reset when the status
register is read. Generates an interrupt when set.
I/O
2
Set when I/O is high; reset when I/O is low.
SUPL
3
Set when a voltage fault is detected; reset when the status register is read.
Generates an interrupt when set.
PROT
4
Set when an over-current or over-heating fault has occurred during a card session;
reset when the status register is read. Generates an interrupt when set.
MUTE
5
Set during ATR when the card has not answered during the ISO 7816-3 time
window (40000 card clock cycles); reset when the next session begins.
EARLY
6
Set during ATR when the card has answered before 400 card clock cycles; reset
when the next session begins.
ACTIVE
7
Set when the card is active (VCC is on); reset when the card is inactive.
I
2C-bus Read from Status Register
The I
2C-bus Read Command from the Status Register follows the format shown in Figure 6. After the
START condition, the master sends a slave address. This address is seven bits long followed by an eighth
bit which is an opcode bit (R/W) – a ‘one’ indicates the master will read data from the status register. After
the R/W bit, the ’zero’ ACK bit is sent to the master by the device. The device now starts sending the 8-bit
status register data to the control register during the DATA bits. After the DATA bits, the ‘one’ ACK bit is
sent to the device by the master. The master should send the STOP condition after receiving the ACK bit.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16LC54C-04I/P | IC MCU OTP 512X12 18DIP |
| 73S8024RN-IL/F | IC SMART CARD INTERFACE 28-SOIC |
| PIC12LCE519-04/SN | IC MCU OTP 1KX12 LV W/EE 8SOIC |
| PIC16F882T-I/SO | IC PIC MCU FLASH 2KX14 28SOIC |
| PIC24F08KL200T-I/ST | IC MCU 16BIT 8KB FLASH 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8010R-IMR/F | 功能描述:I2C 接口集成电路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010R-IMR/F1 | 功能描述:I2C 接口集成电路 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010R-IMR/F2 | 功能描述:I2C 接口集成电路 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8014BL-IL/F | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| 73S8014BN | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Smart Card Interface |
发布紧急采购，3分钟左右您将得到回复。