- 您现在的位置：买卖IC网 > PDF目录16278 > 73S8023C-DB (Maxim Integrated Products)BOARD DEMO 73S8023C 32-QFN PDF资料下载
参数资料
| 型号： | 73S8023C-DB |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/27页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 73S8023C 32-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
DS_8023C_019
73S8023C Data Sheet
Rev. 1.5
11
8
Activation and Deactivation
8.1
Activation Sequence (Synchronous Mode)
The 73S8023C smart card interface IC has an internal ~10 ms delay at power-on reset or on application
of VDD > VDDF
1.
CMDVCC is set low.
. No activation is allowed at this time.
CMDVCC (edge triggered) must then be set low to
activate the card.
The following steps list the activation sequence and the timing of the card control signals when the
system controller sets
CMDVCC low:
2.
Turn on VCC and I/O (AUX1, AUX2) to reception mode at the end of (tACT
3.
RST is a copy of
RSTIN and CLK is a copy of STROBE after (t
).
1).
Figure 3: Activation Sequence – Synchronous Mode
8.2
Deactivation Sequence (Synchronous Mode)
Deactivation is initiated either by the system controller by setting the
CMDVCC high, or automatically in
the event of hardware faults. Hardware faults are over-current, overheating, VDD
1.
RST goes low at time t
fault and card extraction
during the session and are indicated to the system controller by the fall of
OFF.
The following steps list the deactivation sequence and the timing of the card control signals when the
system controller sets the
CMDVCC high or a fault condition sets OFF low:
1
2.
CLK stops low at time t
.
2
3.
I/O goes low at time t
.
3
4.
V
. Out of reception mode.
CC is shut down at time t 4. After a delay t 5 (discharge of the V CC capacitor), VCC is low.
CMDVCC
VCC
IO
CLK
RSTIN
tACT
t1
RST
STROBE
tACT ~= 500s
t1 > 0.5s after tACT, RST = RSTIN, CLK = STROBE
相关PDF资料 |
PDF描述 |
|---|---|
| 73S8010C-DB | BOARD DEMO 73S8010C 28-SOIC |
| NCP303LSN30T1G | IC DETECTOR VOLTAGE 3.0V 5TSOP |
| 73S8010R-DB | BOARD DEMO 73S8010R 28-SOIC |
| DD-DB1-AL202C-FB | DEV BD 20X2 LCD BLU TXT BLK BL |
| NCP301LSN30T1G | IC DETECTOR VOLTAGE 3.0V 5TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8023C-IM/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8023C-IM/F1 | 功能描述:输入/输出控制器接口集成电路 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8023C-IM/F2 | 功能描述:输入/输出控制器接口集成电路 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8023C-IMR/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8023C-IMR/F1 | 功能描述:输入/输出控制器接口集成电路 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。